Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя страница 62

Страница: 62 / 147

STOPPING THE ENGINE

Bring the vehicle to a complete stop before stopping the engine.

NOTE

Stopping the engine with the transmission in gear while the vehicle is moving

could cause loss of rear wheel traction or engine and transmission damage,

which could cause loss of control and serious injury or death. Always stop the

engine after the vehicle is fully stopped and the transmission is in neutral (or

clutch is disengaged). If the engine stops unexpectedly while the vehicle is

moving, guide the vehicle to a safe location off the road and away from traffic.

1. Brake to a complete stop. When nearly stopped, disengage the clutch.

NOTE

As the vehicle slows, disengage the clutch, or downshift each time vehicle

speed reaches a downshift point.

2. When fully stopped, move the ignition switch to the OFF position.

3. Remove the ignition key.

4. Engage the park brake.

OPERATION

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды