Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя

Страница: 81 / 147

COOLANT LEVEL

Always check the coolant level when the engine is cold. Maintain the coolant
level at the “cold” fill level mark

on the recovery bottle

(when the fluid is

cool).

1. Position the vehicle on a level surface.

2. Open the hood.

3. View the coolant level in the recovery bottle.

CAUTION

Escaping steam can cause burns. Never remove the pressure cap while the

engine is warm or hot. Always allow the engine to cool before removing the

pressure cap.

4. If the level is low, slowly remove the pressure cap

. Use a funnel to add

coolant to the fill level mark.

5. Reinstall the pressure cap.

NOTE

If coolant must be added often, or if the recovery bottle runs completely dry,

there may be a leak in the system. Have the cooling system inspected by your

dealer.

MAINTENANCE

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды