Polaris Scrambler 500 4x4 Скачать руководство пользователя

Страница: 71 / 129

EMISSION CONTROL SYSTEMS

Noise Emission Control System

Do not modify the engine, intake or exhaust components, as doing so

may affect compliance with state and local noise level requirements.

Spark Arrestor

Your Polaris vehicle has a spark arrestor that was tested and approved

in accordance with the USDA Forest Service Standard 5100-1C.

Federal law requires that this spark arrestor be installed and functional

when the vehicle is operated on public lands.

Crankcase Emission Control System

This engine is equipped with a closed crankcase system. Blow-by

gases are forced back to the combustion chamber by the intake system.

The system does not allow the blow-by gases to enter the atmosphere.

Exhaust Emission Control System

The emissions from the exhaust of this vehicle are controlled by engine

design, including factory-set carburetion and ignition. The engine and

related components must be maintained at Polaris specifications to

achieve optimal performance.
Adjustment to engine idle is the

only adjustment Polaris

recommends that the operator

perform. Any other adjustments

should be performed by an

authorized Polaris dealer.
The emissions label (1) is located

on the recoil cover.

Содержание Scrambler 500 4x4


































































































































Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды

Polaris Scrambler 500 4x4, Руководство пользователя

Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды