Polaris Scrambler 500 4x4 страница 103 Скачать руководство пользователя

Страница: 103 / 129

100

MAINTENANCE AND LUBRICATION

Filter Systems

Air Filter Service

1. Remove the seat, release

the clips, and remove the

air box cover.

2. Loosen the clamp and remove

the filter.

3. Remove the fabric type pre-filter (1)

from the main filter (2). Wash the

pre-filter in soapy water, then rinse

and let dry.

4. Reinstall the pre-filter over the main

filter. (Replace the main filter if needed.)

5. Reinstall the filter into the air box and tighten

the clamp. Do not over tighten the clamp, as filter damage could

occur.

Breather Filter/Hose

1. Remove the clamps and pull the filter (1)

out of the hoses.

NOTE:

It’s not

necessary to remove the lower hose

from the engine.

2. Inspect the filter for debris. Blow

gently through the filter in the direction

of the arrow to check for clogging.

Replace if needed.

3. Check the hoses for cracks,

deterioration, abrasion, or leaks. Replace as needed.

4. Reinstall the filter and secure the clamps.

NOTE:

The filter is

effective with the arrow pointing in either direction.

Operation of your vehicle without a breather filter can cause

engine damage. Always reinstall the breather filter after

removing for service.

CAUTION

Содержание Scrambler 500 4x4


































































































































Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды

Polaris Scrambler 500 4x4, Руководство пользователя

Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды