Polaris Scrambler 500 4x4 Скачать руководство пользователя

Страница: 52 / 129

OPERATION

Break-In Period

The break-in period for your new 4-cycle Polaris ATV is defined as the

first ten hours of operation, or the time it takes to use the first two full

tanks of gasoline. No single action on your part is as important as

following the procedures for a proper break-in. Careful treatment of a

new engine will result in more efficient performance and longer life for

the engine. Perform the following procedures carefully.

1. Fill the fuel tank with

gasoline (see page 44).

2. Check the oil level on

the dipstick (see page

79). Add the

recommended oil as needed to maintain the oil level in the normal

operating range (1).

3. Drive slowly at first. Select an open area that allows room to

familiarize yourself with vehicle operation and handling.

4. Vary throttle positions. Do not operate at sustained idle.
5. Perform regular checks on fluid levels, controls and areas outlined

on the daily pre-ride inspection checklist. See page 50.

6. Pull only light loads.
7. During the break-in period, change both the oil and the filter at 20

hours or 200 miles.

CAUTION

Excessive heat build-up during the first three hours of

operation will damage close-fitted engine parts. Do not operate

at full throttle or high speeds for extended periods during the

first three hours of use.
Use of any oils other than those recommended by Polaris may

cause serious engine damage. We recommend the use of

Polaris Premium 4 Synthetic Oil for your 4-cycle engine.

ADD 8 OZ.

NORMAL

FULL

Содержание Scrambler 500 4x4


































































































































Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды

Polaris Scrambler 500 4x4, Руководство пользователя

Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды