Polaris Scrambler 500 4x4 страница 115 Скачать руководство пользователя

Страница: 115 / 129

112

MAINTENANCE AND LUBRICATION

Cleaning and Storage

Storage Tips

See page 117 for the part numbers of Polaris products.

Fluid Levels

Inspect the following fluid levels and change if necessary: front

gearcase; transmission; front hubs; brake fluid (change every two years

or as required if fluid looks dark or contaminated).

Engine

1. Support the front end of the machine so the engine is level or tilted

slightly rearward.

2. Remove the spark plug.
3. Rotate the piston to BDC and pour approximately two ounces of

Premium 4 Synthetic 4-cycle oil into the cylinder.

4. Reinstall the spark plug.
5. Apply dielectric grease to the inside of the spark plug cap and install

the cap onto the plug.

6. Turn the engine over several times, using the recoil starter, to

ensure coverage of piston rings, cylinder walls and crankshaft

bearings.

7. Treat the fuel system with Polaris Carbon Clean.
8. If Polaris fuel system additive is not used, the fuel tank, fuel lines,

and carburetor should be completely drained of gasoline.

Engine Anti-Freeze

Test engine coolant strength and change if necessary. Replace coolant

every two years.

Lubricate

Inspect all cables and lubricate with Polaris Cable Lubricant. Follow

lubrication guidelines in the maintenance section of the service or

owner’s manual to completely grease and lubricate the entire vehicle

with Polaris Premium All Season Grease. Apply Polaris O-Ring Chain

Lube to the drive chain(s).

Storage Area/Covers

Set the tire pressure and safely support the ATV with the tires 1-2” off

the ground. Be sure the storage area is well ventilated, and cover the

machine with a genuine Polaris ATV cover.

NOTE:

Do not use plastic

or coated materials. They do not allow enough ventilation to prevent

condensation, and may promote corrosion and oxidation.

Содержание Scrambler 500 4x4


































































































































Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды

Polaris Scrambler 500 4x4, Руководство пользователя

Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды