Polaris Scrambler 500 4x4 Скачать руководство пользователя

Страница: 111 / 129

108

MAINTENANCE AND LUBRICATION

Battery

Battery Storage

When the vehicle is placed in storage for three months or more, the

battery should be removed, stored out of the sun in a cool, dry place

and tested monthly. Before reusing, take the battery to your dealer for

testing and recharging.
Power plug leads may need to be bent down so that the battery cover

can be installed.

Battery Charging

The following battery charging instructions apply only to the

installation of a YUASA activated, sealed battery. Read all

instructions before proceeding with the installation of this battery.
The YUASA activated, sealed battery is already filled with electrolyte

and has been sealed and

fully charged

at the factory.

Do not ever

pry

the sealing strip off or add any other fluid to this battery.

The single most important thing to maintaining a sealed battery is to

keep it fully charged

. Since the battery is sealed and the sealing strip

cannot be removed, you must use a voltmeter or multimeter to measure

DC voltage.
For a refresh charge, follow all instructions carefully.
1. Check the battery voltage with a voltmeter or multimeter. A fully

charged battery will register 12.8 V or higher.

2. If the voltage is less than 12.8 volts, recharge the battery at 1.2

amps or less until the battery voltage is 12.8 V or greater.

NOTE:

When using an automatic charger, refer to the charger

manufacturer’s instructions for recharging. When using a constant

current charger, use the following guidelines for recharging.

An overheated battery could explode, causing severe injury or

death. Always watch charging times carefully. Stop charging if

the battery becomes very warm to the touch. Allow it to cool

before resuming charging.

WARNING

Содержание Scrambler 500 4x4


































































































































Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды

Polaris Scrambler 500 4x4, Руководство пользователя

Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды