Polaris Scrambler 500 4x4 страница 89 Скачать руководство пользователя

Страница: 89 / 129

MAINTENANCE AND LUBRICATION

Adjustments

Brakes

The front and rear brakes are hydraulic disc brakes, activated by

moving the single brake lever toward the handlebar. These brakes are

self-adjusting.
The following checks are recommended to keep the brake system in

good operating condition. Check more often if brakes are used heavily

under normal operation, such as in hilly country or in muddy terrain.

1. Always maintain brake fluid at an adequate level (see page 41).

NOTE:

Under normal operation, the diaphragm extends into the

reservoir as fluid level drops. If the fluid level is low and the

diaphragm is not extended, a leak is likely and the diaphragm should

be replaced. Always fill the reservoir as needed whenever the cover is

loosened or removed to ensure proper diaphragm operation. Use

Polaris DOT 3 brake fluid. Do not overfill.

Never store or use a partial bottle of brake fluid. Brake fluid is

hygroscopic, meaning it rapidly absorbs moisture from the air.

The moisture causes the boiling temperature of the brake fluid to

drop, which can lead to early brake fade and the possibility of

accident or severe injury. After opening a bottle of brake fluid,

always discard any unused portion.

WARNING

An over-full master cylinder may cause brake drag or brake

lock-up, which could result in serious injury or death. Maintain

brake fluid at the recommended level. Do not overfill.

WARNING

Содержание Scrambler 500 4x4


































































































































Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды

Polaris Scrambler 500 4x4, Руководство пользователя

Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды