Polaris Scrambler 500 4x4 Скачать руководство пользователя

Страница: 56 / 129

OPERATION

Starting the Engine

Starting a Warm Engine

Warm engines do not normally require the use of the choke. Excessive

use of the choke can cause the spark plug to become wet fouled.
1. Position the vehicle on a level surface with the transmission in

neutral.

2. Lock the parking brake, turn the fuel tank valve to

, sit on the

vehicle, and turn the engine stop switch to

RUN

3. If the engine has cooled to a point where it does not readily start,

intermittent use of the choke button (pulled half way out) may be

necessary.

4. If the engine is over-choked when warm, depress the throttle lever

fully while cranking to aid in starting.

5. Release the throttle lever immediately after the engine starts. If the

engine does not start and all conditions are favorable, change the

spark plug and try again.

Cold Weather Operation for 4-Cycle Engines

If the ATV is used year-round, check the oil level frequently. A rising

oil level could indicate the accumulation of water in the bottom of the

oil tank. Water in the bottom of the tank can lead to engine damage

and must be drained. Water accumulation increases as outside

temperature decreases.
See your Polaris dealer for engine heater kits, which provide quicker

warm-ups and easier starting in colder weather.

Содержание Scrambler 500 4x4


































































































































Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды

Polaris Scrambler 500 4x4, Руководство пользователя

Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды