Polaris Scrambler 500 4x4 Скачать руководство пользователя

Страница: 109 / 129

106

MAINTENANCE AND LUBRICATION

Spark Arrestor

1. Remove the arrestor clean-out

plug (1) from the bottom of the

muffler.

2. Place the transmission in neutral

and start the engine.

3. Purge carbon from the system by

momentarily revving the engine

several times.

4. If carbon is expelled, cover or plug the

exhaust outlet (2) and rap on the pipe around

the cleanout plug while revving the engine several more times.

5. If particles are still suspected to be in the muffler, elevate the rear

of the vehicle one foot higher than the front. Set the parking brake

and block the wheels. Make sure the vehicle is in neutral and

repeat steps 3 and 4 until no more particles are expelled when the

engine is revved.

6. Stop the engine and allow the arrestor to cool. Reinstall the

arrestor plug and remove the outlet cover or plug.

WARNING

Failure to heed the following warnings while servicing the spark

arrestor could result in serious injury or death.
Do not perform service on the spark arrestor while the system is

hot. Exhaust system temperatures can reach 1000

F. Allow

components to cool sufficiently before proceeding.
Remove any combustible materials from the area.
Wear eye protection.
Do not stand behind or in front of the vehicle while purging.
Never run the engine in an enclosed area. Exhaust contains

poisonous carbon monoxide gas.
Never go under the vehicle while it’s inclined.

Содержание Scrambler 500 4x4


































































































































Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды

Polaris Scrambler 500 4x4, Руководство пользователя

Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды