Polaris Scrambler 500 4x4 страница 77 Скачать руководство пользователя

Страница: 77 / 129

MAINTENANCE AND LUBRICATION

Lubrication Recommendations

NOTE:

Hours are based on 10 mph average. If service is due at 20

hours, the equivalent odometer reading would be 200 miles. Perform

all services at whichever reading is reached first.

Lubrication Chart Key

More often under severe use, such as wet or dusty conditions

Polaris Premium All Season Grease or grease conforming to NLG

No. 2, such as Conoco Superlube M or Mobilegrease Special

Use Polaris Premium U-Joint Lube every 500 miles, before long

periods of storage, or after pressure washing or submerging

∆

When suspension action becomes stiff, or after washing

Item

Lube

Method

Frequency

4-Cycle

Engine

Premium 4

Synthetic 0W40

Add to proper level on dip-

stick.

Check level daily

Brakes

DOT 3 fluid only Maintain level between fill

lines. See page 41.

As required;

change every two

years or 200

hours

Drive chain(s)

O-ring chain

lube or SAE

80/90

Lubricate.

As needed, before

each use in wet

conditions

(1) Transmission

AGL Synthetic

Gearcase Lube

See Page 82.

Change annually

or at 100 hours

(2) Front

Gearcase

Angle Drive

Fluid

See Page 83.

Change annually

or at 100 hours

(3) Front Prop

Shaft U-joints

Grease

Grease fittings.

3 months/50

hours

(4) Front Prop

Shaft Yoke

Grease

Grease fittings

(3 pumps maximum).

3 months/50

hours

(5) Front Drive

Axle (U Joint)

Grease

Locate grease fitting and

grease with grease gun.

Every 3 months or

50 hours

(6) Swing Arm

Bushings

Grease

Locate fittings on swing arm

and grease with grease gun.

Monthly or at 20

hours

(7) Tie Rod Ends

∆

Grease Lift boot, clean away dirt and

grease, apply fresh grease

by hand and reassemble.

Semi-annually

(8) Front Hubs

Premium

Hub Lube

Remove set screw in hubs.

Rotate wheels to 4 O’clock

position. If lubricant is not

visible add more. Reinstall

set screw.

Annually or at 100

hrs.

(9) Ball Joint

Grease

Locate fitting on back side of

struts and grease with

grease gun.

Every 3 months or

50 hours

(10) A-Arms

∆

Grease Locate fittings and grease.

Semi-annually

Содержание Scrambler 500 4x4


































































































































Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды

Polaris Scrambler 500 4x4, Руководство пользователя

Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды