Polaris Scrambler 500 4x4 Скачать руководство пользователя

Страница: 114 / 129

111

MAINTENANCE AND LUBRICATION

Cleaning and Storage

Storage Tips

See page 117 for the part numbers of Polaris products.

Exterior

Make necessary repairs and then clean the ATV thoroughly with mild

soap and warm water to remove all dirt and grime. Don’t use harsh

detergents or high pressure washers. Some detergents deteriorate rubber

parts. Use dish soap type cleaners only. High pressure washers may

force water past seals.

Fuel Stabilizer

Polaris Carbon Clean is a fuel stabilizer and fuel system dryer. It

cleans the fuel system, the combustion chamber and the exhaust ports.

It also prevents bacterial growth and promotes better starting after the

storage period.
1. Fill the fuel tank with fuel and add Polaris Carbon Clean or Fuel

Stabilizer. Follow the instructions on the container for the

recommended amounts.

2. Start the engine and allow it to run for 15-20 minutes so the stabilizer

can disperse through the fuel in the tank and carburetor.

3. Stop the engine, turn the fuel valve off, and drain the carburetor bowl.

Oil and Filter

Warm the engine and change the oil and filter.

Air Filter / Air Box

Inspect and clean or replace the pre-cleaner and air filter. Clean the air

box and drain the sediment tube.

Breather Filter(s)

Inspect and clean or replace the breather filter(s).

Recoil Housing

Remove the recoil housing drain plug and drain any moisture.

Starting the engine during the storage period will disturb the

protective film created by fogging and damage could occur.

Never start the engine during the storage period.

CAUTION

Содержание Scrambler 500 4x4


































































































































Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды

Polaris Scrambler 500 4x4, Руководство пользователя

Результаты поиска

Содержание Scrambler 500 4x4

Отзывы:

Похожие инструкции для Scrambler 500 4x4

Бренды по названию

Популярные бренды