Pioneer PDA-4002 Скачать руководство пользователя страница 113

Страница: 113 / 163

113

Mounting standard metal fixtures (PDM-4001)

3. It is possible to stack up to four units using the multiple installation fixtures. For four-unit stacking, it is necessary to

take measures against falling by either securing the cradle to the floor with anchors, securing the upper portion by

suspending from the ceiling or bolting to the ceiling or securing the back side to the wall with bolts, etc.

Upper portion

To prevent falling, use these holes to secure

the upper portion by suspending from the

ceiling or the wall.

Back side

To prevent falling, use these holes

to secure to the wall, etc.

Secure the cradle using anchors. Moreover, for the actual

examples of installation works in which suspension bolts

and anchors were used, see the attached manual

(ZMZ014) for the installation and implementation of the

exclusive fixture (TVK series) for the system monitor.

Cradle

floor

• Make sure to confirm the strength after installing

anchors. They may come off due to defective
installation or concrete work.

• For detailed information on the size and strength of

anchors, see the product catalogs of anchors, etc.

• We are not responsible for any accidents or damages

caused due to insufficient strength of anchors or
defective anchor installation work.

Caution

Содержание PDA-4002




































































































































































Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды

Pioneer PDA-4002, Техническое руководство

Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды