Pioneer PDA-4002 Скачать руководство пользователя страница 115

Страница: 115 / 163

115

Mounting standard metal fixtures (PDM-4001)

7) Other installation conditions

(1) Wall hanging installation

Two units each of fan units are used for the
upper side and lower side.
Operation guaranteed environment temperature:
0 to 35

(2) Tilted installation (5 to 25 degrees)

Put additional reinforcing crosspieces

Fan units are not used.
Operation guaranteed environment temperature:
0 to 35

* Do not block both sides.

• In case of tilted installation, never fail to provide

necessary reinforcement.

Open

PC-9800 (56.4Hz)

PC-9800 (70.1Hz)

VIDEO

Machintosh (66.7Hz)

VGA (60Hz)

VGA (72.8Hz, 75Hz)

0~35

When connecting laterally, make sure to provide a partition between the

left and right units to be connected.

When installing in a series side by side, there is no need for a partition

between the left and right units to be connected.

PC-9800 (56.4Hz)

PC-9800 (70.1Hz)

VIDEO

Machintosh (66.7Hz)

VGA (60Hz)

VGA (72.8Hz, 75Hz)

0~35

When connecting laterally, make sure to provide a partition between the

left and right units to be connected.

When installing in a series side by side, there is no need for a partition

between the left and right units to be connected.

Содержание PDA-4002




































































































































































Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды

Pioneer PDA-4002, Техническое руководство

Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды