Pioneer PDA-4002 Скачать руководство пользователя страница 128

Страница: 128 / 163

128

When mounting the optional speaker, tighten the PDK-4001 and optional speaker with the mounting screws

supplied with the PDK-4001. However, for the center section with no speaker metal fixture, align the height by

inserting under the speakers the outer diameter

25 mm washers supplied with the speaker.

Fig. 1

Mounting standard metal fixtures
(Precautions for installing the optional speaker)

4.12.4 Precautions for mounting various metal fixtures after the optional speakers are attached to

the plasma display main body

When various metal fixtures are to be mounted after the optional speakers have been mounted to the plasma display,

the following steps and precautions must be observed, depending on the specific type.

1) Tilted stand (PDK-4001)

Washer of

25-mm outer diameter

(supplied with the optional speaker)

Washer
(supplied with the PDK-4001)

Bolt
(supplied with the PDK-
4001)

Washer
(supplied with the
PDK-4001)

Bolt
(supplied with the
PDK-4001)

Содержание PDA-4002




































































































































































Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды

Pioneer PDA-4002, Техническое руководство

Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды