Pioneer PDA-4002 Скачать руководство пользователя страница 54

Страница: 54 / 163

5 4

3.4.11 Installation under the floor

• If protective glass or similar material is used, the following installation conditions must be observed:

600 mm or more

Intake

Exhaust

Protective glass surface

Looking in the direction of the arrow (see the next page)

If the display is used in the closed space, observe the following conditions in the above environment:

≥

20 mm (clearance between the protective glass and PDP)

≥

100 mm (clearance between the PDP and side wall)

≥

50 mm (clearance between the PDP and side wall)

≥

290 mm (clearance between the surface of the PDP and the mounting surface under

the floor)

≥

D – 65 mm

≥

180 mm

≥

600 mm

Special installation (Installation under the floor)

A + 50 mm
or less

60 mm
or less

Exhaust fan

Flow of air from the air conditioner

Intake port

Tempered glass, etc. (permeable)

A + 50 mm
or less

60 mm or
less

Exhaust port

600 mm or more

Floor

Exhaust

PC-9800 (56.4Hz)

PC-9800 (70.1Hz)

VIDEO

Machintosh (66.7Hz)

VGA (60Hz)

VGA (72.8Hz, 75Hz)

Without exhaust fan

0~30

Not usable

With exhaust fan

0~35

50mm

Содержание PDA-4002




































































































































































Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды

Pioneer PDA-4002, Техническое руководство

Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды