Pioneer PDA-4002 Скачать руководство пользователя страница 36

Страница: 36 / 163

3 6

Special installation (Putting in a box) Mesh (side)

Operating this display in confined spaces is not recommended.

• If the display is to be used in confined spaces, observe the following conditions shown in the drawing in a page to the

right:

≥

Use a mesh with aperture efficiency of 50% or more.

•

Keep the temperature in the closed space "Y" and the open space "X" less than the following temperature

range. In particular, the space "Y" should be ventilated sufficiently by the air conditioner or fan so that hot air
is not trapped in the space

. Thus, everywhere in "Y" must be kept less than the following temperature range. If hot

air remains in the closed space, the temperature may rise, causing a malfunction or fire. As a precaution in case of

accidents, the inner wall should have sufficient heat resistance or fire resistance.

Usage temperature conditions (BOX air temperature)

VIDEO

0~35

PC-9800 (56.4Hz)

Machintosh (66.7Hz)

VGA (60Hz)

0~35

PC-9800 (70.1Hz)

VGA (72.8Hz, 75Hz)

0~30

Содержание PDA-4002




































































































































































Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды

Pioneer PDA-4002, Техническое руководство

Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды