Pioneer PDA-4002 Скачать руководство пользователя страница 132

Страница: 132 / 163

132

Before making adjustments

5.1 Before Beginning Adjustments

You can make adjustments to the unit in the following ways:

• With the operating panel of the main unit
• With the remote control unit
• With a PC (through RS-232C control)

Make sure you’ve thoroughly read and understood the following before making any adjustments.

5.1.1 Operating mode

The unit has the following four major operating modes:

Standby Status

Normal Operating Mode

Integrator Mode

<PON>

RS-232C Adjustment Mode

Menu Mode

<POF>

STANDBY/ON

STANDBY/ON

(Note 1)

DISPLAY

PICTURE PARAMETER

CONTRAST

See the description provided in

BRIGHT.

“5.3 Outer control by RS-232C”.

COLOR (Note:1)

TINT (Note:1,4)

SHARPNESS (Note:1)

CLK.FRQ. (Note:2)

CLK.PHS. (Note:2)

HOR.POS. (Note:2)

HOR.POS.

VER.POS. (Note:2)

VER.POS.

INIT.

SCART RGB (Note:6)

WHITE BALANCE

R HIGH
G HIGH
B HIGH
R LOW
G LOW
B LOW
INIT.

ADDITIONAL SET UP

COLOR MODE
BAUD RATE
AUTO RGB2
MP MODE (Note:5)
NTSC MASK (Note:4)
FULL MASK
OSD
FOUR METER (Note:3)

TOTAL INITIALIZE

Note 1: Only when VIDEO and Y/C are input.
Note 2: Only when RGB1 and RGB2 are input.
Note 3: Only indication
Note 4: Only when NTSC signal, no signal, or no applicable signal is input (VGA, Macintosh, PC-9800 inputs).

Cannot adjust when PAL signals are input <PAL signals can be input only for PDP-V402E>.

Note 5: Only when signals other than the NTSC signal are input.
Note 6: PDP-V402 only

indicates operating mode and
status.
indicates button operations on
the remote or on the main unit’s
operating panel.

indicates RS-232C command op-
erations.

Содержание PDA-4002




































































































































































Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды

Pioneer PDA-4002, Техническое руководство

Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды