Pioneer PDA-4002 Скачать руководство пользователя страница 52

Страница: 52 / 163

5 2

Special installation (Installation on the floor)

3.4.10 Installation on the floor

This display is designed to accommodate floor installation, but certain specific installations may interfere with adequate

ventilation. Always observe the following conditions:

Use

plate metal that keeps all single holes clear

and has dimensions no larger than those given in the following

table.

Leave adequate ventilation space between the display and the floor.

Use plate metal having sufficient strength, and attach at the four points indicated in the following drawing (four-

point mounting).

Recommended ambient operating temperatures are listed in the following table. Operate the display within this

temperature range.

The ceiling should closely approximate a perfectly flat plane. Keep deformation pressures upon the display, such

as twisting and bending, at or below 1 mm.

Do not block this area at the top or bottom.

75mm

40mm

Do not block this area at the left or right.

40mm

75mm

Floor

694 mm (center indicated)

75mm 75mm

PC-9800 (56.4Hz)

PC-9800 (70.1Hz)

A size

VIDEO

Machintosh (66.7Hz)

VGA (60Hz)

VGA (72.8Hz, 75Hz)

50 mm or more

0~40

0~35

Working temperature requirements

50mm

Floor

* The same conditions apply to the working temperature requirements for a speaker system (PDP-S03-LR).

Содержание PDA-4002




































































































































































Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды

Pioneer PDA-4002, Техническое руководство

Результаты поиска

Содержание PDA-4002

Отзывы:

Похожие инструкции для PDA-4002

Бренды по названию

Популярные бренды