manualshive.com logo in svg

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 104 / 112

Поделиться
Скачать
Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 104

IB IL 24 PSDO 8-PAC

104 / 112

PHOENIX CONTACT

7619_en_05

D 4

Validation

Checklist for validating the safety module

Device type / Equipment identification

Version: HW/FW/FW

Date

Editor

Test engineer 

Comment

No

.

Requirement (mandatory)

Yes

Comment

1

Have all the mandatory requirements for the "Planning" checklist been 

met?

2

Have all the mandatory requirements for the "Assembly and electrical in-

stallation" checklist been met?

3

Have all the mandatory requirements for the "Startup and parameteriza-

tion" checklist been met?

4

Does the parameterization of the safe outputs correspond to the version 

and the actual connection of the controlled devices?

5

Has the assignment of the actuators to the outputs and the variables of the 

safe application program been tested (also as online status in 

SafetyProg)?

6

Has a function test been performed to check all safety functions in which 

the module is involved?

7

Have measures been taken to achieve a specific Cat.?

8

Do all cables correspond to the specifications?

9

Does the power supply correspond to the specifications for the protective 

extra-low voltage in accordance with PELV?

10

Has the power supply of U

M

 and U

S

 in the Inline system from a power sup-

ply unit been implemented?

11

Is external protection of the module implemented (according to the speci-

fications in this user manual for supply voltage U

M

)?

12

INTERBUS-Safety: Is the shutdown time to be parameterized imple-

mented according to the planning? (Uniform shutdown time, derived from 

the system specifications or shutdown time per channel)

13

Have measures been taken to prevent simple tampering?

14

Have measures been taken to prevent plugs being mixed up?

15

Are requirements for the actuators and cable installation observed accord-

ing to the SIL/SILCL/Cat./PL to be achieved?

16

Are the specifications for the parameterization for each channel imple-

mented?

17

Have test intervals been defined for testing the shutdown capability of the 

actuators, if this is required to achieve a SIL/SILCL/Cat./PL?

18

For PROFIsafe: Is the F_iPar_CRC parameter greater than 0 for all de-

vices?

Содержание IB IL 24 PSDO 8-PAC

















































































































Отзывы:

Нет отзывов