Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 61

Страница: 61 / 112

Connection examples for safe outputs

7619_en_05

PHOENIX CONTACT

61 / 112

Typical parameterization

According to the “Value range of switch-off time” and “Switch-off time” parameters, in this

example, the shutdown time is 20 x 10 ms = 200 ms.

According to the “Value range of switch-off delay for stop category 1” and “Switch-off delay

for stop category 1” parameters, in this example, the switch-off delay is 30 x 1 s = 30 s.

Parameterization

Parameterized as

Comment

Assignment

Used

Output

Single-channel

Shutdown time (in software:

switch-off time)

(INTERBUS-Safety only)

Application-specific

Value range of the shutdown

time (in software: value range

of switch-off time)

(INTERBUS-Safety only)

Value x 10 in ms

Application-specific

Switch-off delay for stop cate-

gory 1

Enabled

Or disabled

Switch-off delay for stop cate-

gory 1

Application-specific

Value range of switch-off delay

for stop category 1

Value in s

Application-specific

Enable

Enabled

Or disabled

Test pulses (output disabled)

(in software: test impulses

(output switched off))

Enabled

Or disabled

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 61 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: