Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 66

Страница: 66 / 112

IB IL 24 PSDO 8-PAC

66 / 112

PHOENIX CONTACT

7619_en_05

When connecting the supply voltages, use the diagnostic and status indicators to check

whether the module has started up correctly or whether any errors are indicated. For instruc-

tions on how to proceed in the event of an error, please refer to Section “Errors: Messages

and removal” on page 69.

Carry out the necessary parameterization.

Section “Parameterization of the safety module” on page 47

Documentation for the SafetyProg software

(INTERBUS-Safety)

Documentation for the configurable safety module used

(SafetyBridge)

Documentation for the controller used (PROFIsafe)

Program the safety function.

User manuals for the function blocks used

Documentation for the SafetyProg software

(INTERBUS-Safety)

Documentation for the configurable safety module used

(SafetyBridge)

Documentation for the controller used (PROFIsafe)

For PROFIsafe: When verifying the safety function, check

whether the F_iPar_CRC parameter is greater than 0 for all

devices. If not, modify the settings.

Checklist “Validation” on page 104

Quick Start Guide for configuring Inline modules with safe in-

puts or outputs under PROFIsafe on your controller

Perform a function test and validation. Check whether the

safety function responds as planned during programming

and parameterization.

Checklist “Validation” on page 104

Table 7-1

Steps for startup (Fortsetzung)

Step

Relevant section and literature

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 66 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: