Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 96

Страница: 96 / 112

IB IL 24 PSDO 8-PAC

96 / 112

PHOENIX CONTACT

7619_en_05

B 3.2

Diagnostic messages for parameter errors for

SafetyBridge

Table B-3

iParameter parameter errors

Error Code

(Hex)

Error cause

Remedy

03F2

iPar_CRC is incorrect

Check iParameters, repeat calculation.

03FA

iPar_CRC is not equal to F_iPar_CRC

Apply correct value.

03FB

PST_Device_ID is incorrect

Correct value (20

hex

for IB IL 24 PSDO 8-PAC).

03FC

F_Destination_Address in the iParameters is incorrect

Correct value.

Make sure that the value set under F_Destina-

tion_Address and the value that you have set

via the 10-pos. DIP switch are the same.

03FD

Incorrect order of iParameter blocks

Check infrastructure components.

Table B-4

F-Parameter parameter errors

Error code

Error cause

Remedy

dec

hex

1088

440

The parameterized SafetyBridge address does not

match the address set on the safety module.

Make sure that the addresses are the same.

1089

...

1094

441

...

446

Internal error

Please contact Phoenix Contact.

The configurable safety module detected a distortion in

the configuration and parameter data record.

Attempt transmission again.

If the error occurs permanently, the data record

in the controller is distorted. In this case, you

can get SAFECONF to generate a new data re-

cord.

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 96 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: