Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 33

Страница: 33 / 112

Inline potential and data routing, and Inline connectors

7619_en_05

PHOENIX CONTACT

33 / 112

Inline potential and data routing, and Inline connectors

3.1

Inline potential and data routing

In order to operate the safety module it must be integrated in an Inline station within the

INTERBUS-Safety, SafetyBridge or PROFIsafe system.

The bus signals are transmitted via the Inline data jumpers. The required supply voltages

are transmitted via the Inline potential jumpers.

The segment circuit is looped through the safety module and is available again after the

module. The segment circuit is not accessed in the safety module.

3.2

Supply voltage U

Supply the 24 V supply voltage U

24 V

at a bus coupler or a suitable power terminal

(IB IL 24 PWR IN/R). The 7.5 V voltage U

is generated from this 24 V supply voltage in the

bus coupler or power terminal. It is supplied to the safety module via the Inline potential

jumper U

The supply voltage

is used to supply the communications power. For the technical data

for the supply voltage U

, please refer to “Supply voltage U

(logic)” on page 84.

The maximum current carrying capacity for the supply voltage U

is 2 A.

This current carrying capacity can be reduced if certain terminals are used. Please refer to

the information in the terminal-specific data sheets.

3.3

Supply voltage U

Supply the supply voltage at a bus coupler or a power terminal. It is supplied to the safety

module via the Inline potential jumper U

The supply voltage

is used to supply the output circuits. For the technical data for the

supply voltage U

, please refer to Section “Supply voltage: U

(actuators)” on page 84.

The maximum current carrying capacity for the main circuit U

is 8 A (total current with the

segment circuit that is not used in the safety terminal). This current carrying capacity can be

reduced by certain terminals. Please refer to the information in the terminal-specific data

sheets.

For more detailed information on potential and data routing within an Inline station, please

refer to the IL SYS INST UM E user manual.

WARNING: Loss of the safety function when using unsuitable power supplies

Please note for the voltage supply at the bus coupler or power terminal that:

Only power supplies according to EN 50178/VDE 0160 (PELV) may be used.

Make sure that the output voltage of the power supply does not exceed 32 V even in the

event of a fault.

Please also observe the points in Section “Electrical safety” on page 10.

WARNING: Loss of the safety function when using unsuitable power supplies

Please observe the points in Section “Electrical safety” on page 10.

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 33 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: