Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 84

Страница: 84 / 112

IB IL 24 PSDO 8-PAC

84 / 112

PHOENIX CONTACT

7619_en_05

Safety characteristic data according to EN ISO 13849-1

Achievable performance level

PL d (single-channel)

PL e (two-channel)

Depends on the parameterization and wiring (see Section

“Connection options for actuators depending on the param-

eterization” on page 22 and Section “Connection examples

for safe outputs” on page 55)

Diagnostic coverage (DC)

99 %

Mean time to dangerous failure (MTTFd)

For single-channel assignmennt: 100 years

For two-channel assignmennt: 100 years

Supply voltage U

(logic)

Current consumption

230 mA, maximum

The safety terminal is supplied with communications power via the bus coupler or a designated power terminal

in the station. Potential routing is used for the communications power in the Inline station. For the technical

data, please refer to the data sheet for the bus coupler or power terminal used.

Supply voltage: U

(actuators)

Nominal voltage

24 V DC according to EN 61131-2 and EN 60204

Tolerance

-15%/+20% including an entire AC voltage component with

peak value of 5%

Ripple

3.6 V

Permissible voltage range

19.2 V DC to 30.0 V DC, including all tolerances, ripple in-

cluded

Current consumption

30 mA, typical (all outputs set) (plus actuator current)

Permissible interrupt time

10 ms

Within this time, the output voltage for the safe outputs fails

as the outputs are not internally buffered.

The safety terminal is supplied with main voltage U

via the bus coupler or a power terminal in the station.

Potential routing is used for the main voltage in the Inline station. For the technical data, please refer to the

data sheet for the bus coupler or power terminal used.

WARNING: Loss of the safety function when using unsuitable power supplies

Only use power supplies according to EN 50178/VDE 0160 (PELV).

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 84 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: