Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 20

Страница: 20 / 112

IB IL 24 PSDO 8-PAC

20 / 112

PHOENIX CONTACT

7619_en_05

2.4

Safe digital outputs

The safety module has safe positive switching digital outputs, which can be used as follows:

–

For two-channel assignment:

–

For single-channel assignment:

Technical data

For the technical data for the safe outputs, please refer to Page 85.

Parameterization

The individual safe digital outputs of a safety module can be parameterized differently. This

means that the outputs can be adapted to various operating conditions and different safety

integrity levels (SIL, SILCL, Cat., PL) can be implemented.

In order to achieve a high level of error detection, the test pulses must be enabled. If this is

not possible for the connected loads, the test pulses can be disabled. However, in this case

error detection is reduced.

For information on parameterization, please refer to Section “Parameterization of the safe

outputs” on page 50.

Diagnostics

Diagnostics are provided via both the local diagnostics indicators and the diagnostic mes-

sages, which are transmitted to the safe controller (INTERBUS-Safety, PROFIsafe) or to a

configurable safety module (SafetyBridge).

For information on the diagnostic messages of the outputs, please refer to Section “Safe dig-

ital output errors” on page 71.

–

Four two-channel outputs

–

Eight single-channel outputs

The safety integrity level (SIL, SILCL, Cat., PL) and error detection that can be achieved

depend on the parameterization, the structure of the actuator, and the cable installation

(see “Connection examples for safe outputs” on page 55).

CAUTION: Diagnostic data is not safety-related

Do not use the diagnostic data to execute safety-related functions or actions.

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 20 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: