Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 100

Страница: 100 / 112

IB IL 24 PSDO 8-PAC

100 / 112

PHOENIX CONTACT

7619_en_05

D 1

Planning

Checklist for planning the use of the safety module

Device type / Equipment identification

Version: HW/FW/FW

Date

Editor

Test engineer

Comment

Requirement (mandatory)

Yes

Comment

Has the current module user manual been used as the basis for plan-

ning?

Revision:

Are the actuators permitted for connecting to the module (as per techni-

cal data and parameter setting options)?

Has the power supply been planned according to the specifications for

the protective extra-low voltage in accordance with PELV?

Has the power supply of U

and U

from a power supply unit been

planned?

Is external protection of the module planned (according to the specifica-

tions in this user manual for supply voltage U

INTERBUS-Safety: Is the shutdown time to be parameterized specified

(uniform shutdown time, derived from the system specifications or shut-

down time per channel)?

Are measures planned to prevent simple tampering?

Are measures planned to prevent connectors being mixed up?

Are requirements for the actuators and cable installation observed ac-

cording to the SIL/SILCL/Cat./PL to be achieved and the appropriate im-

plementation planned?

Are the specifications for the parameterization for each channel de-

fined?

Have test intervals been defined for testing the shutdown capability of

the actuators, if this is required to achieve a SIL/SILCL/Cat./PL?

Has it been ensured that any person intentionally starting hazardous

movements can only do so with a direct view of the danger zone?

Does the planned use correspond to the intended use?

Are the ambient conditions observed according to the technical data?

Are the test intervals specified?

Has the switch-off delay for stop category 1 been observed in the calcu-

lation of the total response time for the machine/system?

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 100 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: