Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 103

Страница: 103 / 112

Startup and parameterization

7619_en_05

PHOENIX CONTACT

103 / 112

D 3

Startup and parameterization

Checklist for startup and parameterization of the safety module

Device type / Equipment identification

Version: HW/FW/FW

Date

Editor

Test engineer

Comment

Requirement (mandatory)

Yes

Comment

Was startup completed according to the specifications (specifications

from the planning phase or according to the user manual)?

During startup, is it ensured that any person starting hazardous move-

ments intentionally can only do so with a direct view of the danger zone?

Are all parameters parameterized for the outputs?

Are both channels for outputs that are parameterized as two-channel

matched to each other?

INTERBUS-Safety: Are the shutdown times for the outputs calculated

and parameterized?

Are the output test pulses parameterized according to the actuator to be

connected?

Has the switch-off delay for stop category 1 been observed in the calcu-

lation of the total response time for the machine/system?

Requirement (optional)

Yes

Comment

Are the safety distances to be maintained dimensioned according to the

implemented response and delay times (reaction times)?

Date

Signature (editor)

Date

Signature (test engineer)

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 103 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: