background image

Digiplex/DigiplexNE LCD Keypad 37

n

8.0 GLOSSARY

Access Alarm:

An audible or silent warning generated by the
reader to indicate that a protected door has not
closed within the programmed time allowed or
that a protected door was opened without an
“Access Granted” or “Request for Exit” signal. If
the Access Alarm is programmed to be audible,
the reader assigned to the door can beep. This
event is logged in the Event Buffer, but can only
be seen through an Access Control keypad
(DGP2-641AC).

Access Control:

A system designed to monitor and control the
admission through specific doors.

Access Control

A tag assigned to a User Access Code used to

card:

identify the user to the Access Control system.
By presenting the tag to a reader, the system
can verify whether the tag is valid (see Valid
Access Control Card).

Access Denied:

An Access Control term for the system’s refusal
to admit access through a protected door.

Access Granted:

An Access Control term for the system
permitting admission through a protected door.

Access Level:

The combination of Access Control doors that
will be assigned to users through their User
Access Codes. Users will only be permitted to
enter through the protected doors that are
programmed in their Access Level.

Burglar Alarm:

An audible or silent warning sent to the control
panel indicating that an armed zone in the
system has been breached. This event is logged

Содержание DGP2-641













































Отзывы: