Panasonic Windea VGD13113W Скачать руководство пользователя страница 83

Страница: 83 / 118

復旧/警報音停止

RESET/ STOP ALARM

電源火災

POWER

FIRE

復旧/警報音停止

RESET/ STOP ALARM

電源

POWER

ガス

GAS

復旧/警報音停止

RESET/ STOP ALARM

電源火災

POWER

FIRE

ガス

GAS

警報音停止

STOP ALARM

電源

POWER

●

The gas icon will turn off after approximately

3 minutes, and the area around the MENU

button will flash in red.

●

Once gas is no longer detected, the alarm

stops. Also, the GAS indicator, area around the

MENU button, ALARM indicator on the call

sub-base unit, and door phone alarm display

indicator turn off.

●

The GAS indicator appears only on the base
unit.

●

The area around the MENU button, GAS
indicator, ALARM indicator, and alarm display
indicator continue to flash until there is no more
gas in the gas detector.

●

The gas icon can also be turned off within
3 minutes. ( Page 155)

●

The detector disconnected icon will turn off

after approximately 1 minute, and the area

around the MENU button will flash in red.

●

Once the detector wiring is reconnected,

the alarm stops. Also, the area around the

MENU button, FIRE indicator, and door

phone alarm display indicator turn off.

●

After pressing the STOP ALARM button,
touching on the base unit will cause
the screen to return to the waiting state, and
the area around the MENU button will light
up in red. To display the detector
disconnected icon, touch on the Top
Menu screen. ( Pages 20 to 21)

●

The FIRE indicator continues to appear, the
area around the MENU button continues to
light up or flash, and the alarm display
indicator continues to flash until the detector
wiring is reconnected.

●

The detector disconnected icon can also be
turned off within 1 minute. ( Page 155)

160

161

When the gas detector detects gas, the system
reports a gas leak.

In the Event of Detector Disconnection

In the Event of a Gas Leak

In the Event of Fire or Disconnection

In the Event of a Gas Leak or Disconnection

Confirm that system components are properly installed before using the system.

STOP ALARM

button

FIRE

indicator

appears

in red

Door phone

Alarm display indicator

Flashes in red
Alarm is sounding

When detector wiring becomes disconnected,
the system reports a disconnection.

●

Press the STOP ALARM button.

(The alarm can also be turned off from

the building manager room.)

●

The alarm can be disabled.

How to stop the alarm sound

Procedures during alarms

(Beeps)

Detector

disconnected

icon appears

in red

MENU button

Call sub-base unit

Alarm is sounding

Cautions

●

Shut off the main gas valve and open

the windows and doors to ventilate the room.

How to stop the alarm sound

Procedures during alarms

STOP ALARM

button

Gas icon

flashes in yellow

GAS

indicator

flashes

in yellow

GAS indicator

flashes in yellow

Door phone

Alarm display indicator

Flashes in red
Alarm is sounding

(Rapid beeps)

Gas leak.

After approx.
40 seconds

button

Call sub-base unit

ALARM indicator

Flashes in red
Alarm is sounding

The gas detector

detects a gas leak

Appears in white

MENU button

Consult with the management

company or the company that

installed the system.

Gas icon

flashes in yellow

Confirm button

●

Press the STOP ALARM button on the base

unit. Note that the gas detector alarm will

not turn off.

Pressing the STOP ALARM button on

the call sub-base unit with monitor does

not stop the alarms on other equipment.

●

Exposure to moisture containing alcohol from

cooking sauces and wines, etc. may cause

the gas detector to generate false

detections.

The system can be configured to

trigger the gas leak alarm as the gas

detector activates.

Consult with the management

company or the company that

installed the system.

Note

INTRODUCTION

USUAL USAGE

SETTING ACCORDING TO

YOUR PREFERENCES

OPERATIONS AND MEASURES

WHEN ALARM GOES OFF

SECURITY ALARM SETTING

AND DISARMING

RECORD

MANAGEMENT

OTHER

Installer

Setting

Installer

Setting

●

For base unit

●

For base unit

●

For base unit

●

For call sub-base unit with monitor

and do not appear in the call
sub-base unit with monitor

Содержание Windea VGD13113W























































































































Результаты поиска

Содержание Windea VGD13113W

Отзывы:

Похожие инструкции для Windea VGD13113W

Бренды по названию

Популярные бренды

Panasonic Windea VGD13113W, Простое руководство

Результаты поиска

Содержание Windea VGD13113W

Отзывы:

Похожие инструкции для Windea VGD13113W

Бренды по названию

Популярные бренды