Panasonic Inverter R32 Series Скачать руководство пользователя страница 97

Страница: 97 / 259

1-10-14

Recommended Wire Length and Wire Diameter for Power Supply System

Control wiring

(C) Inter-unit

(between outdoor

and indoor units)

control wiring

(D) Remote control

wiring

(E) Control wiring

for group control

0.75 mm

(AWG #18)

Use shielded

wiring*

0.75 mm

(AWG #18)

0.75 mm

(AWG #18)

Max. 1,000 m

Max. 500 m

Max. 200 m (Total)

NOTE

With ring-type wire terminal.

(1) Before wiring, confirm the rated voltage of the unit as shown on its nameplate, then carry out the wiring closely

following the wiring diagram.

WARNING

(2) This equipment is strongly recommended to be installed with Earth Leakage Circuit Breaker (ELCB)

or Residual Current Device (RCD). Otherwise, it may cause electrical shock and fire in case of

equipment breakdown or insulation breakdown.

Earth Leakage Circuit Breaker (ELCB) must be incorporated in the fixed wiring in accordance with

the wiring regulations.

The Earth Leakage Circuit Breaker (ELCB) must be an approved 10 - 16 A, having a contact

separation in all poles.

(3) To prevent possible hazards from insulation failure, the unit must be grounded.

(4) Each wiring connection must be done in accordance with the wiring system diagram. Wrong wiring may cause the

unit to misoperate or become damaged.

(5) Do not allow wiring to touch the refrigerant tubing, compressor, or any moving parts of the fan.
(6) Unauthorized changes in the internal wiring can be very dangerous. The manufacturer will accept no responsibility

for any damage or misoperation that occurs as a result of such unauthorized changes.

(7) Regulations on wire diameters differ from locality to locality. For field wiring rules, please refer to your LOCAL

ELECTRICAL CODES before beginning.

You must ensure that installation complies with all relevant rules and regulations.

(8) To prevent malfunction of the air conditioner caused by electrical noise, care must be taken when wiring as follows:

The remote control wiring and the inter-unit control wiring should be wired apart from the inter-unit power wiring.

Use shielded wires for inter-unit control wiring between units and ground the shield on both sides.

(9) If the power supply cord of this appliance is damaged, it must be replaced by a repair shop designated by the

manufacturer, because special-purpose tools are required.

General Precautions on Wiring

Electrical Wiring

Indoor unit

Type

(B) Power supply

Time delay fuse or

circuit capacity

2.5 mm

U2, E1, T2, F1

Max. 130 m

10-16 A

Type

(B) Power supply

Time delay fuse or

circuit capacity

2 mm

Max. 130 m

10-16 A

SM830266-00_大洋州向けR32シングルTD&SM.indb 14

18/03/29 10:20:00

Содержание Inverter R32 Series




































































































































































































































































Результаты поиска

Содержание Inverter R32 Series

Отзывы:

Бренды по названию

Популярные бренды

Panasonic Inverter R32 Series, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание Inverter R32 Series

Отзывы:

Бренды по названию

Популярные бренды