manualshive.com logo in svg

Panasonic Inverter R32 Series, Технические данные и руководство по обслуживанию

Поделиться
Скачать
Panasonic Inverter R32 Series Скачать руководство пользователя страница 105

1

1-11-4

(D)  When outdoor units are stacked
 

Only two outdoor units can be stacked.

 

For drain treatment, a space of at least 400 mm is required between the upper and lower outdoor units.

 

Close the area A (gap between the upper outdoor unit and lower outdoor unit) so that the outlet air does not bypass there.

(1)  Obstruction on the air outlet side

(2)  Obstruction on the air inlet side

a

b

Area A

a

500 mm or more

b 400 mm

a

b

Area A

a

200 mm or more

b 400 mm

(E)  When outdoor units are installed in rows, such as on a rooftop (L 

<

 H)

(1)  One outdoor unit installed in each row

a

b

c

d

H

L

a

500 mm or more

b 300 mm or more
c 1,000 mm or more
d 50 mm or more

(2)  Two or more units installed side by side.

a

b

c

A

L

H

d

e

a

1,000 mm or more

b 400 mm or more
c 2,000 mm or more
d 250 mm or more

e

250 mm or more

The dimensional relationship between H, A, and L is as shown 
in the following table.
                                                            Unit: mm

A

L 

≤

 H

150

H 

<

 L

Installation is not allowed.

The values described above are the least space to optimize 
application performance.
If any service area is needed for service according to field 
circumstance, obtain enough service space.

In case of multiple installations

●

  Concrete block foundation should be used and well drained. 

Be sure that the foundation height is kept at least more than 
50 mm from the ground.

●

  Base leg should be fixed by inserting the flat washer (field 

supply) and single nut (field supply) onto the anchor bolt 
(M8, field supply). Protrusion length of anchor bolt should be 
13 mm or less and fastening height of nut should be 12 mm 
or less.

 

Note: 

 

If the anchor bolt is longer and the fastening height of

 

n

ut is higher, the front panel may be damaged when

 

i

nstalling or removing it.

●

  Use lug bolts or equal to bolt down unit, reducing vibration 

and noise.

Air intake

Air intake

Min. 150 mm

Anchor bolts 

(4 pieces)

Air discharge

13 mm or less

(Protrusion length of anchor bolt)

12 mm or less

(Fastening height of nut)

01_301769_2WAY_eng.indb   14

2018/3/20   9:14:56

Air-Discharge Chamber for Top Discharge

  it is difficult to keep a space of min. 50 cm between the air 

discharge outlet and an obstacle.

  the air discharge outlet is facing a sidewalk and discharged 

hot air annoys passers-by.

Air discharge

provided with a platform and snow-proof duct.

Installing the Unit in Heavy Snow Areas

In locations with strong wind, snow-proof ducting should likewise 

much as possible.

 Countermeasures against snow and wind

In regions with snow and strong wind, the following problems 
may occur when the outdoor unit is not provided with a platform 
and snow-proof ducting:

Without snow-
proof ducting 
(Low platform)

With snow-proof 
ducting  
(High platform)

a)  The outdoor fan may not run and damage of the unit may be 

caused.

b)  There may be no airflow.
c)  The tubing may freeze and burst.
d)  The condenser pressure may drop because of strong wind, 

and the indoor unit may freeze.

s

a

e

r

A

 

w

o

n

S

 

y

v

a

e

H

 

n

i 

n

o

i

t

a

ll

a

t

s

n

I 

r

o

f

 

s

n

o

i

t

u

a

c

e

r

P  

(1)  The platform should be higher than the maximum snow 

depth +50 cm.

(2)  The 2 anchoring feet of the outdoor unit should be used for 

the platform, and the platform should be installed beneath 
the air intake side of outdoor unit.

(3)  The platform foundation must be firm and the unit must be 

secured with anchor bolts.

(4)  Be sure to install the outdoor unit so that snowfall or icicle 

from the roof will not affect the unit.

(5)  In case of installation on a roof subject to strong wind, 

countermeasures must be taken to prevent the unit from 
being blown over.

Dimensions of Snow / Wind-proof Ducting and 

Refrigerant Tubing Space for Installation

Min. 100

Min. 100 146

146

Unit: mm

Duct

Outdoor Unit

 

 

Air Intake

Platform (foundation)

Higher than the maximum 

snow depth + 50 cm

About 1/2 of the unit height

Duct

 

Refer to the diagrams below for the installation 
location which is exposed to strong wind.

If a strong wind of more than 5m/sec blows to the area directly 

outcome:
“Reduced capacity”, “Increased frost formation during heating” 
or “Operation stopped due to increased pressure”.
Should an exceptionally strong wind blow to the area directly 
in front of the discharge of the outdoor unit, there is a risk of 
damage due to the fan's high-speed reverse rotation.

Wall / outer wall

Place unit at right 
angle to wind's 
direction. 

Place unit at appropriate 
angle to wind's direction 
so that discharge faces 
towards building or wall.

When installing unit in a place 

where it will be affected by 

typhoon or strong wind such as 

wind blowing between buildings, 

including rooftop of building and 

a place where there is no building 

overturn prevention wire, etc. 

Strong wind

Strong wind

Air intake side

Air intake

Air discharge

Keep space for installation 

and maintenance service

Wall / outer wall

•  When installing the unit in a place where it will be affected by 

typhoon or strong wind, provide a windbreak plate (optional).

•  When installing the unit in a place where there is no obstacles 

in surroundings, provide a wind direction guide (optional).

01_301769_2WAY_eng.indb   15

2018/3/20   9:14:57

SM830266-00_大洋州向けR32シングルTD&SM.indb   4

18/03/29   10:20:05

Содержание Inverter R32 Series




































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды