manualshive.com logo in svg

Panasonic Inverter R32 Series, Технические данные и руководство по обслуживанию

Поделиться
Скачать
Panasonic Inverter R32 Series Скачать руководство пользователя страница 249

2

2

2-8

Blinking “

 

 

” indicator

 Cancel

Auto address

1

Assigning

Display During Auto Address Setting

●

  On the surface of outdoor unit control P.C. board

1 2

LED

Blinks alternately

*   Do not short circuit the A.ADD pin again during auto address setting. 

 

LEDs 1 and 2 go out and address setting is interrupted.

*   When auto address setting is normally completed, both LEDs 1 and 2 go out. 

 

In other cases, correct settings referring to the following table and perform auto address setting again.

●

  Contents of LEDs 1 and 2 on outdoor unit control P.C. board

 : ON     : Blinking     : OFF

LED1 LED2

Remark

Normal operation

Pre-trip (High pressure protection)

LED1 Blinking : 0.8sec-ON / 0.3sec-OFF

Pre-trip (other)

LED1 Blinking : 0.5sec-ON / 0.5sec-OFF

Auto address 

setting

Under auto address setting

Blinking alternately

Auto address setting alarm

Follow the blinking patterns of each alarm

Alternate blinking of outdoor unit LED 
during alarms

LED1 blinks M times, and then LED2 blinks N times. The cycle then repeats.
M=2:P alarm, 3:H alarm, 4:E alarm, 5:F alarm, 6:L alarm, N=alarm No
Example: LED1 blinks 4 times, then LED2 blinks 6 times. The cycle then repeats. Alarm is “E06”

Power ON 
sequence

No communication from indoor units in system

If it is not possible to advance to 3 repeats 1

→

2

Communication received from 1 or more 
indoor units in system

At 3, advances to normal control

Regular communication OK 

 

(Capacity and unit quantity match)

Refrigerant recovery mode

●

  Display of remote controller

CZ-RTC5A / CZ-RTC5B 

CZ-RTC4

01_301769_2WAY_eng.indb   35

2018/3/20   9:15:14

2

-9.  Indicating (marking) the indoor and outdoor unit combination number  

Indicate (mark) the number after auto address setting is completed.

●

  So that the combination of each indoor unit can be easily checked when multiple units are installed, ensure that the indoor and 

outdoor unit numbers correspond to the system address number on the outdoor unit control PCB, and use a magic marker or similar 
means which cannot be easily erased to indicate the numbers in an easily visible location on the indoor units (near the indoor unit 
nameplates).
Example:  (Outdoor) 1 - (Indoor) 1

 

(Outdoor) 2 - (Indoor) 1

●

  These numbers will be needed for maintenance. 

Be sure to indicate them.

Use the remote controller to check the indoor unit address.

High-spec Wired Remote Controller (CZ-RTC5A / CZ-RTC5B)

(3)   The “Simple settings” screen appears on the LCD display.

Select the “Unit no.” by pressing the 

 or 

 

button for changes.

Simple settings

Unit no.

Code no.

Set data

01

3-1

0001

Sel.

Next

20:30 (THU)

The indoor unit fan operates only at the selected indoor unit.

START

[

]

20:30 (THU)

Timer remote controller (CZ-RTC4)

<If 1 indoor unit is connected to 1 remote controller>

(1)

   Press and hold the

 

 button and

 

 button for 4 

seconds or longer (simple settings mode).

(2)

   The address is displayed for the indoor unit that is 

connected to the remote controller.

 

( Only the address of the indoor unit that is connected to 

the remote controller can be checked.)

(3)   Press the

 

 button again to return to normal remote 

controller mode.

Number changes to indicate 
which indoor unit is currently 
selected.

Indoor unit address

(1)  

Keep pressing the

 

 ,

 

 and 

 buttons 

simultaneously for 4 or more seconds. 
The “Maintenance func” screen appears on the LCD 
display.

Maintenance func

1. Outdoor unit error data

2. Service contact
3. RC setting mode
4.Test run

Sel.

Page [

] Confirm

20:30 (THU)

(2)

   Press the 

 or 

 button to see each menu.

If you wish to see the next screen instantly, press the 

 or 

 button.

Select “7. Simple settings” on the LCD display and press 

the 

 button.

Maintenance func

5. Sensor info.
6. Servicing check

8. Detailed settings

Sel.

Page [

] Confirm

20:30 (THU)

7. Simple settings

 

01_301769_2WAY_eng.indb   36

2018/3/20   9:15:15

SM830266-00_大洋州向けR32シングルTD&SM.indb   8

18/03/29   11:58:29

Содержание Inverter R32 Series




































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды