Panasonic Inverter R32 Series Скачать руководство пользователя страница 217

Страница: 217 / 259

1-11-116

(4) Connect the drain hose.

Do not enforce the base of the drain hose when making a connection.

Insert securely the drain hose into the PVC pipe.

When installing the drain hose extension, connect with an optional drain hose.

After connection, bundle with armoring tape.

Make sure not to make the drain hose trapped.

Insulate the connected part of the drain hose with the tubing insulation and check whether or not the water drains.

Wall

PVC pipe

(VP-16)

Drain hose ø16 mm

Indoor side

In the case of using

PVC pipe (VP-16)

Wall

Indoor side

Drain hose ø16 mm

Over 700 mm

PVC pipe (VP-30)

•

Adhere with PVC adhesive.

Reducing adaptor (30×20)

PVC pipe

(VP-20)

In the case of using

PVC pipe (VP-30)

(5) When there is a long horizontal drain hose runs with very little slope to the run, water is likely to remain inside the hose. Slant the

drain hose downward slightly to the outdoors and insulate it with the insulation.

Slant downward not to remain water inside the drain hose.

Make sure tubing does not become trapped.

Do not let the tip of the drain hose dip into the drain water.

Do not leave the drain hose in the sewerage. This will cause the heat exchanger erosion damage caused by the corrosive gas such

as hydrogen sulfide occurred inside the sewerage and lead to a gas leak.

Slant

downward

Trap

To mount and unmount indoor unit

How to mount indoor unit
1. To install the indoor unit, mount the indoor unit onto the tabs on the upper part of the installation plate.

2. Hold down the air discharge outlet and press the lower part of the indoor unit until it clicks to securely fasten to the 2 tabs on the

lower part of the installation plate.

3. Close the front panel and ensure that the panel is perfectly stable.

Tabs

Installation plate

Tabs

Push by both hands.

Connecting part

Tabs

Installation plate

How to unmount indoor unit
Press the 2 PUSH marks on the lower part of the indoor unit and unlatch the tabs. Then lift the indoor unit and unmount.

1 Push by both hands.

Connecting part

Tabs

Installation plate

2 Remove

SM830266-00_大洋州向けR32シングルTD&SM.indb 116

18/03/29 10:21:21

Содержание Inverter R32 Series




































































































































































































































































Результаты поиска

Содержание Inverter R32 Series

Отзывы:

Бренды по названию

Популярные бренды

Panasonic Inverter R32 Series, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание Inverter R32 Series

Отзывы:

Бренды по названию

Популярные бренды