manualshive.com logo in svg

Panasonic Inverter R32 Series, Технические данные и руководство по обслуживанию

Поделиться
Скачать
Panasonic Inverter R32 Series Скачать руководство пользователя страница 175

1

1-11-74

Installing the Drain Pipe

(1)   Prepare standard hard PVC pipe (O.D. 32 mm) for the drain 

and use the supplied hose band to prevent water leaks.

 

The PVC pipe must be purchased separately.

 

 The transparent drain part on the unit allows you to check 
drainage.

 

CAUTION

 

 Do not use adhesive tape at the drain connection port on 
the indoor unit.

 

 Insert the drain pipe until it contacts the socket, and then 
secure it tightly with the hose band.

 

 Do not bend the supplied drain hose, please keep it 
straight.

 

 Tighten the hose clamps so their locking nuts face 
upward. (Fig. 1-11-27)

Hose band (Supplied)

Drain insulator (Field supply)
(The thickness must be at 
least 8 mm.)

Drain hose with 
heat insulator 
(Supplied)

PVC pipe 
(O.D. ø32) 
(Field supply)

To be glued

Please do not glue.

Make sure that there is no clearance here.

Fig.1-11-27

(2)   After connecting the drain pipe securely, wrap the supplied 

packing and drain pipe insulator around the pipe, then secure 
it with the vinyl clamps . (Fig. 1-11-28)

Drain insulator (Field supply)

Vinyl clamps 
(Field supply)

Fig.1-11-28

NOTE

Make sure the drain pipe has a downward gradient (1/100 
or more) and that there are no water traps.

 

CAUTION

• 

 Do not install an air bleeder as this may cause water to 
spray from the drain pipe outlet. (Fig. 1-11-29)

Air bleeder

Prohibited

Fig.1-11-29

• 

 If it is necessary to increase the height of the drain pipe, 
the section directly after the connection port can be 
raised a maximum of 500 mm. Do not raise it any higher 
than 500 mm, as this could result in water leaks.

Drainage hole

Foam drain socket 

(Supplied)

Hose band 
(Supplied)

Fig.1-11-30

 

 Do not install the pipe with an upward gradient from the 
connection port. This will cause the drain water to 

fl

 ow 

backward and leak when the unit is not operating. 
(Fig. 1-11-31)

Prohibited

Upward gradient

Fig.1-11-31

 

 Do not apply force to the piping on the unit side when 
connecting the drain pipe. The pipe should not be allowed to 
hang unsupported from its connection to the unit. Fasten the 
pipe to a wall, frame, or other support as close to the unit as 
possible. (Fig. 1-11-32)

Support pieces

Fig.1-11-32

 

 Make sure all connecting PVC pipes are supported to the roof 
structure, and the drain line is installed straight.

Connecting Duct to Indoor Unit

(1)   Install the duct (Field supply) for the Dimension of the 

installation hole. 

 

Use M5 self-tapp Screws for installation see the Figure 1-11-21.

(2)  The duct connection of the air outlet needs thermal insulation.

Thermal insulator 
(Local arrangement) 

Air outlet

Fig.1-11-33

NOTE

• 

Select an air-intake grille with a filter at a local shop.

• 

 To get clean air and to extend the service life of the 
air conditioner, an air filter must be installed in the air 
intake. For installation and cleaning the air filter, consult 
your dealer or service center.

SM830266-00_大洋州向けR32シングルTD&SM.indb   74

18/03/29   10:20:58

Содержание Inverter R32 Series




































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды