manualshive.com logo in svg

Panasonic Inverter R32 Series, Технические данные и руководство по обслуживанию

Поделиться
Скачать
Panasonic Inverter R32 Series Скачать руководство пользователя страница 200

1

1-11-99

 

SELECTING THE INSTALLATION SITE (Type F1)

Indoor Unit

AVOID:

  areas where leakage of flammable gas may be expected.
  places where large amounts of oil mist exist.
  direct sunlight.
  locations near heat sources which may affect the 

performance of the unit.

  locations where external air may enter the room directly. 

This may cause “condensation” on the air discharge ports, 
causing them to spray or drip water.

  locations where the remote controller will be splashed with 

water or affected by dampness or humidity.

  installing the remote controller behind curtains or furniture.
  locations where high-frequency emissions are generated.

DO:

  select an appropriate position from which every corner of the 

room can be uniformly cooled.

  select a location where the ceiling is strong enough to 

support the weight of the unit.

  select a location where tubing and drain pipe have the 

shortest run to the outdoor unit.

  allow room for operation and maintenance as well as 

unrestricted airflow around the unit.

  the limitation of the tubing length between the indoor and

the outdoor units should be referred to the Installation
Instructions of the outdoor unit.

 

 

 

  allow room for mounting the remote controller about 1m off 

the floor, in an area that is not in direct sunlight or in the flow 
of cool air from the indoor unit.

25 cm

40 cm

65 cm

25 cm

HOW TO INSTALL THE INDOOR UNIT

 

Low Silhouette Ducted Type (Type F1)

 

Required Minimum Space for Installation and Service

  This air conditioner is usually installed above the ceiling so that the indoor unit and ducts are not visible. Only the air intake and air 

outlet ports are visible from the unit bottom.

Minimum space for installation and service

Type

60, 71

100, 125, 140

A (Length)

1,067

1,467

636

33.4

33.4

B

D

C

D

154

(150)

54

700

30

290

255

15

140

23

23

113

65

70

90

26.1

300

186

27

256

172

280

g

h

f

i

c

d

b

a

e

j

Unit: mm

Type

A

B

C

D

E

F

60, 71

1,067

1,000

750 (Pitch 150 × 5)

21

792

16

100, 125, 140

1,467

1,400

1,050 (Pitch 150 × 7)

71

1,192

20

Unit: mm

Air intake port side

Air outlet duct side

F

-ø3 holes

E

 (Flange O.D.)

A

 (Suspension bolt pitch)

a

)  Refrigerant tubing joint (liquid tube)

b

)  Refrigerant tubing joint (gas tube)

c

)  Upper drain port VP25 (O.D. 32 mm)

  200 mm flexible hose supplied

d

)  Bottom drain port VP25 (O.D. 32 mm)

e

)  Suspension lug (4 – 12 × 30 mm)

f

 )  Power supply outlet

g

)  Fresh air intake port (ø150 mm)

h

)  Flange for flexible air outlet duct

i

 )  Electrical component box

j

 )  Filter

Inspection

access

450 × 450

(Field supply)

Unit: mm

A

 (Suspension bolt pitch)

Min. 250

Electrical

component box

Inspection

access

450 × 450

Refrigerant

tubing

Min.650

Indoor unit

Min.400

Min.

250

636

Unit: mm

  It is recommended that space be provided (450 × 450 mm) for checking and servicing the electrical system.

Detailed dimensions of indoor unit

SM830266-00_大洋州向けR32シングルTD&SM.indb   99

18/03/29   10:21:12

Содержание Inverter R32 Series




































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды