Panasonic Inverter R32 Series Скачать руководство пользователя страница 252

Страница: 252 / 259

2-11

-10. Table of Self-Diagnostic Functions and Corrections

ON:

Blinking:

OFF:

Abnormal

display

Wireless remote

controller

receiver display

Alarm contents

Error location

Operation

Timer

Standby

Remote controller • Indoor Unit

E01

Operating lamp

blinking

• Faulty remote controller

• Replace the remote controller

• Disconnection / Contact failure of remote controller wiring • Correct the remote controller wiring
• CHK (check) pins on the indoor unit control PCB are

short circuited

• Remove the short

• In the case of non-group control :

Power supply OFF of

outdoor unit

Disconnection / Contact failure of inter-unit wiring

• In the case of group control :

Automatic address

operation was not carried out

• Execute auto address setting

• Faulty setting of EEPROM (IC010) on indoor unit

• Replace the indoor unit EEPROM

E02

• Faulty remote controller

• Replace the remote controller

• Wrong wiring of remote controller

• Correct the remote controller wiring

E03

• Error in indoor unit receiving signal from remote

controller

(central)

• Check the indoor unit control PCB

• Check the remote controller wiring

• Check the inter-unit control wiring

E04

andby

blinking

• Disconnection / Contact failure of inter-unit wiring

• Faulty indoor unit control PCB

• Faulty outdoor unit control PCB

• Communication circuit fuse (F302) on indoor unit control

PCB opened

• Check the electrical connection of inter-unit control wiring

• Replace the indoor unit control PCB

• Replace the outdoor unit control PCB

• Check the electrical connection of fuse (F302) on indoor

unit control PCB

In the case of the fuse opened on an indoor unit control

PCB, after correcting wiring connection, it substitutes an

EMG plug for OC plug

• Fuse on outdoor unit control PCB opened

nce failure of an outdoor fan motor is considered as a

cause, both outdoor unit control PCB and outdoor unit

fan motor are exchanged simultaneously

• In the case of the fuse opened on an outdoor unit control

PCB, replace both outdoor unit control PCB (CR/HIC) and

outdoor unit fan motor simultaneously

E08

Operating lamp

blinking

• Duplication of indoor unit address setting

• Indoor unit address re-setting

E09

• Error because of more than one remote controller setting

to main

• Correct the setting

E18

• Disconnection of wiring between main unit and additional

units

• Contact failure of wiring

• Faulty indoor unit control PCB (main or addition)

• Correct the wiring connection

• Replace the wiring

• Replace the indoor unit control PCB

F01

Operating

and

mer

lamp blinking

ternately

• Indoor heat exchanger temperature sensor (E1) trouble

• Check the indoor unit heat exchanger temperature sensor

(E1)

• Check the indoor unit control PCB

F02

• Indoor heat exchanger temperature sensor (E2) trouble

• Check the indoor unit heat exchanger temperature sensor

(E2)

• Check the indoor unit control PCB

F10

• Indoor air temperature sensor (TA) trouble

• Check the indoor unit air temperature sensor (TA)

• Check the indoor unit control PCB

F29

Operating

and

mer

lamp blinking

multaneously

• Indoor unit EEPROM trouble

• Check the indoor unit EEPROM

• Check the indoor unit control PCB

L02

Operating

and

andby

mps blinking

multaneously

• Setting error, indoor / outdoor unit type / model miss-

matched

• Address re-setting after correcting the combination of units

L03

• Duplication of main indoor unit address in group contro

• Correct the group (main and addition)

L07

• Group control wiring is connected to individual control

indoor unit

• Correct the indoor unit address

L08

• Indoor unit address is not set

• Correct the indoor unit address

L09

• Indoor unit capacity is not set

• Correct the capacity setting of indoor units

P01

Timer and

standby

mp blinking

ternately

• Indoor unit fan motor locked

• Indoor unit fan motor layer short

• Contact failure in thermostat protector circuit

• Remove the cause

• Replace the fan motor

• Correct the wiring

P09

• Faulty wiring connections of (ceiling) indoor unit panel

• Correct the wiring connection

P10

• Faulty drain pump

• Drainage failure

• Contact failure of float switch wiring

• Repair / Replace

• Correct

• Correct the wiring

P11

• Faulty drain pump

• Drain pump locked

• Repair / Replace

• Remove the cause

P12

• Indoor unit fan motor locked

• Faulty wiring connections of indoor unit fan motor

• Remove the cause

• Correct the wiring

01_301769_2WAY_eng.indb 37

2018/3/20 9:15:16

ON:

Blinking:

OFF:

Abnormal

display

Wireless remote

controller

receiver display

Alarm contents

Error location

Operation

Timer

Standby

Outdoor Unit

E06

andby

blinking

• Disconnection / Contact failure of inter-unit wiring

• Disconnection of inter-unit wiring

• Communication circuit fuse (F302) on indoor unit

control

PCB

opened

• Correct the inter-unit control wiring

Check the electrical connection of fuse (F302) on indoor

unit control PCB

In the case of the fuse opened on an indoor unit control

PCB, after correcting wiring connection, it substitutes an

EMG plug for OC plug

• Indoor unit control PCB address settings error

• Indoor unit address re-setting

E12

Operating lamp

blinking

• Auto address setting start is prohibited

• Check the inter-unit control wiring

E14

• Duplication of main unit in group control

• Check the inter-unit control wiring

• Check the indoor unit combination

E15

andby lamp

blinking

Automatic

address

arm

• The total capacity of indoor units are too

low

• Check the inter-unit control wiring

• Check the indoor and outdoor unit control PCB

E16

• The total capacity of indoor units are too

high

• The number of indoor units

two or more

E20

• No indoor unit connected

E24

• Outdoor unit communication error

• Check the outdoor unit control PCB

E29

• Outdoor unit communication error

• Check the outdoor unit control PCB

F04

Operating

and

mer

lamp blinking

ternately

• Compressor discharge temperature sensor (TD) trouble

• Check the compressor discharge temperature sensor (TD)

• Check the outdoor unit control PCB

F06

• Outdoor heat exchanger temperature sensor (C1)

trouble

• Check the outdoor unit heat exchanger temperature

sensor (C1)

• Check the outdoor unit control PCB

F07

• Outdoor heat exchanger temperature sensor (C2)

trouble

• Check the outdoor unit heat exchanger temperature

sensor (C2)

• Check the outdoor unit control PCB

F08

• Outdoor air temperature sensor (TO) trouble

• Check the outdoor air temperature sensor (TO)

• Check the outdoor unit control PCB

F12

• Compressor suction temperature sensor (TS) trouble

• Check the compressor suction temperature sensor (TS)

• Check the outdoor unit control PCB

F31

Operating

and

mer

lamp blinking

ternately

• Outdoor unit EEPROM trouble

• Check the outdoor unit EEPROM

• Check the outdoor unit control PCB

H01

Timer lamp

blinking

• Primary (input) overcurrent detected

• Check the refrigerant cycle (abnormal overload operation)

• Check the outdoor unit control PCB

• Check the power supply

H02

• PAM trouble

• Check the outdoor unit control PCB

• Compressor locked

• Check the power supply

H03

• Primary current CT sensor failure

• Check the outdoor unit control PCB

H31

• HIC trouble

• DC voltage not detected

• Check the outdoor unit control PCB

• Check the HIC

• Compressor locked

• Valve blockage

L04

Operating

and

andby

mps blinking

multaneously

• Duplication of outdoor unit address

• Check the inter-unit control wiring

L10

• Outdoor unit capacity is not set or setting error

• Replace the outdoor unit EEPROM

• Capacity value re-setting

L13

• Indoor unit type setting error

• Type of indoor/outdoor units is different

• Replace the indoor unit EEPROM

• Check the outdoor unit control PCB

• Check the type of IU and OU, and re-set address

L18

• 4-way valve locked trouble / operation failure

• Check the 4-way valve

• Check the 4-way valve wiring

• Check the outdoor unit control PCB

P03

Operating

and

andby

lamp

blinking

alternately

• Compressor discharge temperature trouble

• Check the refrigerant cycle (gas leak)

• Trouble with the electronic expansion valve

• Check the discharge temperature sensor (TD)

P04

• Compressor discharge pressure trouble

• Check the refrigerant cycle

• Valve blockage

• Heat exchanger obstruction

P05

• Open phase detected

• AC power supply trouble

• Check the power supply

• Check the reactor wiring

• Check the outdoor unit control PCB

• Check the compressor wiring

01_301769_2WAY_eng.indb 38

2018/3/20 9:15:16

SM830266-00_大洋州向けR32シングルTD&SM.indb 11

18/03/29 11:58:31

Содержание Inverter R32 Series




































































































































































































































































Результаты поиска

Содержание Inverter R32 Series

Отзывы:

Бренды по названию

Популярные бренды

Panasonic Inverter R32 Series, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание Inverter R32 Series

Отзывы:

Бренды по названию

Популярные бренды