manualshive.com logo in svg

Panasonic Inverter R32 Series, Технические данные и руководство по обслуживанию

Поделиться
Скачать
Panasonic Inverter R32 Series Скачать руководство пользователя страница 146

1

1-11-45

Panel for Cassette (ECONAVI type)

CZ-KPU3A
Applicable indoor unit : 4-Way Cassette
Accessories Supplied

Part Name

Figure

Q’ty

Remarks

ECONAVI 
panel

1 ECONAVI type

Screw

4 4 × 12

Operating 
Instructions

1

Installation 
Instructions

1

Since the accessories need for installation work, do not dispose 
of them until the unit of work is complete.

CAUTION ON INSTALLATION

Criteria for Human Detection Area

  A place where the blind angle of the Human Detection Sensor cannot detect human.

 Install the panel for cassette (ECONAVI type) so that human motion can be detected.

  If there is a heat source or cooling unit in the detection area, the sensor cannot occasionally detect properly.
 The Floor Temperature Sensor detects within the sensor area of Human Detection Sensor.

Human Detection Sensor

Floor Temperature Sensor

Detection area of Human Detection Sensor

1 m above floor visual range

Installation 
height: 
2.7 - 5 m

Detection area of Floor Temperature Sensor

Approx. ø7 - 9 m

Criteria of human detection sensor area
Installation height of indoor unit 2.7 m : Approx. ø7 m
Installation height of indoor unit 4 m : Approx. ø8 m
Installation height of indoor unit 5 m : Approx. ø9 m

Do not install at the following locations. (Cause of trouble and malfunction)

 

•  Humid, oily, frequent vibration 

 

•  Direct sunlight and near by heat source

 

•  Frost 

SM830266-00_大洋州向けR32シングルTD&SM.indb   45

18/03/29   10:20:35

Содержание Inverter R32 Series




































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды