Panasonic Inverter R32 Series Скачать руководство пользователя страница 81

Страница: 81 / 259

1-9-2

•

Type U2

When an External Air Intake Flange (ø100) is in Use

External Air Intake Volume and Resistance and

Operation Noise Characteristics within the Unit

• Calculate the operation noise when external air is being

fed by combining the noise when only external air is being

fed as shown in the graph for operation noise

characteristics and the operation noise of the unit as

stipulated in the catalogue.

• The operation noise conforms to JIS standards and

constitute measurements taken in an anechoic chamber

1.5 m directly beneath the indoor unit.

Under normal circumstances, the values shown here are

greater owing to the effects of surrounding noise and

reverberation when the unit is actually installed.

The amount of external air that is possible to feed

when it is fed directly into the unit (ø100)

Type

100

60 71

125 140

ermissible Air Intake

olume (m³/h)

NOTE

The operation noise for models that use small units is lower,

so use values that are within the range shown in the above

table.

Using values that exceed these will result in noise when only

external air is fed being louder than the noise emitted from the

unit.

With the External Air Intake Flange Attached

Resistance within the Unit (

External Air Intake

olume (m

/h)

External Air Intake

olume (m /h)

xte

rna

Air Intak

e dB(A)

Operation Noise

(External Air Intake Only)

100

Type U2

Resistance within the unit (Pa)

Noise with only External

Air Intake dB(A)

External Air Intake Volume & Resistance Within Unit/

Operation Noise Characteristics

With the External Air Intake Chamber Attached

Use the following diagram along with

the section "1-10-1. Precautions

Regarding External Air Intake".

In a Case of External Air Intake

Using Air Intake Chamber (CZ-FDU3+CZ-ATU2)

• Calculate the operation noise when external air is being

fed by combining the noise when only external air is being

fed as shown in the diagram for operation noise

characteristics and the operation noise of the unit as

stipulated in the catalogue.

•

The amount of external air that is possible to feed

when external air intake chamber is in use

(CZ-FDU3+CZ-ATU2)

The operation noise for models that use small units is

lower, so use values that are within the range shown in

the above table. Using values that exceed these will

result in noise when only external air is fed being louder

than the noise emitted from the unit.

Permissible air intake

volume (m

/h)

The operation noise conforms to JIS standards and

constitute measurements taken in an anechoic chamber

1.5m directly below the indoor unit. Under normal

circumstances, the diagram shown above is greater owing

to the effects of surrounding noise and reverberation when

the unit is actually installed.

CAUTION

100

80
70

40
30
20

-10

40
30
20

100

150

200 240

Resistance within the unit

(High speed wind)

Operation noise

(External air intake only)

Filter chamber

(CZ-FDU3)

Kit for external air intake (for chamber)

(CZ-ATU2)

Connection duct: diameter ø100

Type

190

240

100

240

125 140

Duct (ø1

) for Connecting

the External Air Intake Flange

SM830266-00_大洋州向けR32シングルTD&SM.indb 2

18/03/29 10:19:47

Содержание Inverter R32 Series




































































































































































































































































Результаты поиска

Содержание Inverter R32 Series

Отзывы:

Бренды по названию

Популярные бренды

Panasonic Inverter R32 Series, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание Inverter R32 Series

Отзывы:

Бренды по названию

Популярные бренды