manualshive.com logo in svg

Panasonic Inverter R32 Series, Технические данные и руководство по обслуживанию

Поделиться
Скачать
Panasonic Inverter R32 Series Скачать руководство пользователя страница 4

iii

 WARNING

• 

When performing piping work, do 
not mix air except for specified 
refrigerant

 (R

32

)

 in refrigeration  

cycle. It 

causes capacity down, and  

risk of 

explosion and injury due to  

cycle. 

high 

tension inside the refrigerant 

• If the refrigerant comes in contact 

with a flame, it produces a toxic 
gas.

• Do not add or replace refrigerant 

other than specified type. It may 
cause product damage, burst and 
injury, etc.

• Ventilate the room immediately, in the 

event that is refrigerant gas leaks during 
the installation. Be careful not to allow 
contact of the refrigerant gas with a 
flame as this will cause the generation 
of toxic gas.

• Keep all tubing runs as short as 

possible.

• Use the flare method for connecting 

tubing.

• Apply refrigerant lubricant to the 

matching surfaces of the flare and union 
tubes before connecting them, then 
tighten the nut with a torque wrench for 
a leak-free connection.

• Check carefully for leaks before starting 

the test run.

• Do not leak refrigerant while piping work 

for an installation or re-installation, and 
while repairing refrigeration parts.  
Handle liquid refrigerant carefully as it 
may cause frostbite.

• Under no circumstances shall potential 

sources of ignition be used in the 
searching or detection of refrigerant 
leaks.

• A halide torch (or any other detector 

using a naked flame) shall not be used.

• Electronic leak detectors may be used 

to detect refrigerant leaks but, the 
sensitivity may not be adequate, or 
may need re-calibration. (Detection 
equipment shall be calibrated in a 
refrigerant-free area.)

• Ensure that the detector is not a 

potential source of ignition and is 
suitable for the refrigerant used.

• Leak detection equipment shall be set 

     at a percentage of the lower flammable 

      limit (LFL) of the refrigerant and shall be 

        calibrated to the refrigerant employed 

          and the appropriate percentage of gas

            (25 % maximum) is confirmed.

  •

 

Leak detection fluids are suitable for 

use with most refrigerants but the use of 
detergents containing chlorine shall be 
avoided as the chlorine may react with 
the refrigerant and corrode the copper 
pipe-work.

• If

 

a

 

leak is suspected, all naked flames 

shall be removed/extinguished.

• If

 

a

 

leakage of refrigerant is found which 

requires brazing, all of the refrigerant 
shall be recovered from the system, or 
isolated (by means of shut off valves) 
in a part of the system remote from the 
leak. Oxygen free nitrogen (OFN) shall 
then be purged through the system both 
before and during the brazing process.

When Servicing

• Contact to the sales dealer or service 

dealer for a repair.

• Be sure to turn off the power before 

servicing.

• Turn the power OFF at the main 

power box (mains), wait at least 10 
minutes until it is discharged, then 
open the unit to check or repair 
electrical parts and wiring.

• Keep your fingers and clothing away 

from any moving parts.

• Clean up the site after you finish, 

remembering to check that no metal 
scraps or bits of wiring have been left 
inside the unit.

01_301040_EU_Eng.indb   4

2018/2/1   15:30:10

 WARNING

• This product must not be 

modified or disassembled under 
any circumstances. Modified or 
disassembled unit may cause fire, 
electric shock or injury.

• Do not clean inside the indoor and 

outdoor units by users. Engage 
authorized dealer or specialist for 
cleaning.

• In case of malfunction of this 

appliance, do not repair by 
yourself. Contact to the sales 
dealer or service dealer for a 
repair and disposal.

 CAUTION

• Ventilate any enclosed areas 

when installing or testing the 
refrigeration system. Leaked 
refrigerant gas, on contact 
with fire or heat, can produce 
dangerously toxic gas.

• Confirm after installation that 

no refrigerant gas is leaking. If 
the gas comes in contact with a 
burning stove, gas water heater, 
electric room heater or other 
heat source, it can cause the 
generation of toxic gas.

Others

When disposal of the product, do follow 

the precautions in

 Section

 “RECOVERY”  

on page 2-16 and comply with national 

regulations.

 WARNING

• 

Do not sit or step on the 
unit. You may fall down 
accidentally.

 CAUTION

• 

Do not touch the air inlet or 
the sharp aluminum fins of  
the outdoor unit. You may get  
injured.

• 

Do not stick any object into 
the FAN CASE.  
You may be injured and the  
unit may be damaged.

01_301040_EU_Eng.indb   5

2018/2/1   15:30:10

SM830266-00_大洋州向けR32シングルTD&SM.indb   3

18/03/27   10:55:48

Содержание Inverter R32 Series




































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды