Panasonic Inverter R32 Series Скачать руководство пользователя страница 245

Страница: 245 / 259

2-4

-5. Test Run Using the Remote Controller

High-spec Wired Remote Controller (CZ-RTC5A / CZ-RTC5B)

(1)

Keep pressing the

and

buttons

simultaneously for 4 or more seconds.
The “Maintenance func” screen appears on the LCD
display.

Maintenance func

1. Outdoor unit error data

2. Service contact
3. RC setting mode
4.Test run

Sel.

Page [

] Confirm

20:30 (THU)

(2)

Press the

button to see each menu.

If you wish to see the next screen instantly, press the

button.

Select “4. Test run” on the LCD display and press the

button.

Maintenance func

1. Outdoor unit error data
2. Service contact
3. RC setting mode

4.Test run

Sel.

Page [

] Confirm

20:30 (THU)

Change the display from OFF to ON by pressing the

button. Then press the

button.

[

] Confirm

Test run

Change

20:30 (THU)

Test run

START

[

]

20:30 (THU)

(1)

(4)

(3) Press the

button. “TEST” will be displayed on the

LCD display.

TEST

START

[

]

20:30 (THU)

(4)

Press the

button. Test run will be started.

Test run setting mode screen appears on the LCD display.

TEST

20:30 (THU)

COOL

MODE

Timer remote controller (CZ-RTC4)

(1)

Press the remote controller

button for 4 seconds or longer.

Then press the

button.

●

“

” appears on the LCD display while the test run is in progress.

●

The temperature cannot be adjusted when in Test Run mode.

(This mode places a heavy load on the machines.

Therefore use it only when performing the test run.)

(2)

The test run can be performed using the HEAT, COOL, or FAN

operation modes.

N OT E

The outdoor units will not operate for approximately 3 minutes after the
power is turned ON and after operation is stopped.

(3) If correct operation is not possible, a code is displayed on the remote

controller LCD display.

(

See the section “

-10. Table of Self-Diagnostic Functions and

Corrections” and correct the problem.)

(4)

After the test run is completed, press the

button again.

Check that “

” disappears from the LCD display.

(To prevent continuous test runs, this remote controller includes a timer
function that cancels the test run after 60 minutes.)
* If the test run is performed using the wired remote controller, operation

is possible even if the cassette-type ceiling panel has not been
installed. (“P09” display does not occur.)

01_301769_2WAY_eng.indb 31

2018/3/20 9:15:08

SM830266-00_大洋州向けR32シングルTD&SM.indb 4

18/03/29 11:58:17

Содержание Inverter R32 Series




































































































































































































































































Результаты поиска

Содержание Inverter R32 Series

Отзывы:

Бренды по названию

Популярные бренды

Panasonic Inverter R32 Series, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание Inverter R32 Series

Отзывы:

Бренды по названию

Популярные бренды