Panasonic Elite Big PAC-i S-200PE3E5B, Технические данные и руководство по обслуживанию

Страница: 292 / 316

8 8
Control of 2WAY SYSTEM
2. Wireless Remote Controller
Optional Controller (Remote Controller)
Wireless Remote Controller CZ-RWSU3 / CZ-RWSC3 / CZ-RWSK2
8-19. Names and Functions
1
2
3
4
5
6
7
8
9
10
12
11
13
14
15
16
1. Operation Display
Displays the operation status.
(The figure shows all the statuses.)
2. Start/Stop
button Pressing this button once starts and
pressing again stops the operation.
The auto-flap display may be different,
depending on the installed unit.
3. Fan speed
button
4. Swing/Wind
Direction button
5. Timer setting
button
Use for operating with a timer.
6. Reset button
Use this button after changing the
batteries.
7. Cover
Press at the top center and then
slide down.
8. Transmitter
12. Mode Select
button
Press to switch the operation mode.
14. Address
button
16. Clock button Use this button to set the clock.
13. Ventilation
button
Use this button when connected to
an aftermarket fan. Pressing this
button starts and stops the fan.
When the air conditioner is started
or stopped, the fan starts or stops at
the same time. ( appears on the
display of the remote controller
when the fanis operating.)
15. Sensor button Use this button to activate the
temperature sensor on the remote
controller instead of the one on the
indoor unit. The temperature sensor
on the indoor unit is selected before
shipment. At this time is shown
9. Remote controller
sensor
Detects the temperature at the
remote controller when detection
has been switched to the remote
controller by the sensor button.
11. Filter button CZ-RWSC3
Press to turn off the filter lamp on
the receiver.
10. Temperature
setting buttons
raises the temperature setting
1 at a time.
lowers the temperature setting
1 at a time.
REMOTE CONTROLLER
From this page on the names of remote controller’s
buttons will be indicated with the above illustrations.
E.g.: Start/Stop button
One remote controller can control a group of up to eight indoor units.
on the display.
Control of 2WAY SYSTEM
2. Wireless Remote Controller
1. Receiver Receives the signal sent from the
remote controller.
This lamp is lit when the unit is
operating.
When an error occurs, one of the
lamps flashes. When a display
lamp is blinking, refer to " Before
Requesting Service ".
2. Emergency
operation button Display lamps
When the heater is working, the
lamp lights at the following times.
When the thermostat has operated
during defrosting at the time of the
startup.
The lamp flashes when an error
occurs. 5. Standby lamp
3. Operating lamp
This lamp is lit when the timer is set. 4. Timer lamp
6. Filter lamp
This lamp is for notifying you when
the filter needs to be cleaned.
If a heat pump model is being used, it will beep twice and the operating lamp will light up on the display; if the timer and standby
lamps blink alternately, a conflict between the heating and cooling exists, so the unit cannot operate in the desired mode.
(On models that do not have an Auto function, even if Auto is selected, it works in the same way.)
RECEIVER
CZ-RWSU3
CZ-RWSC3
When the local operation is disabled by such as the centralized control, and if the Start, Stop, Mode or Temperature setting
buttons are pressed, the unit will beep five times and the change will not be made.
NOTE
1
2
34
56
ADDRESS 1
ADDRESS 2
ADDRESS 3
REM SUB/MAIN
1 2 3 4
Front side Rear side
1
2
3 4 5
8-16
SM830276-00_欧州向け R32シングル TD＆SM.indb 16 19/02/18 11:16:06