Panasonic AJ-PX5100G, Руководство по эксплуатации

Страница: 230 / 263

– 230 –
Chapter 8 Network Connection — Network settings
[DEFAULT GATEWAY]:
Default gateway (Factory setting: [192.168.0.254])
[PRIMARY DNS]:
Primary DNS server setting (Factory setting: [0.0.0.0]) (When [DHCP] is set to [ENABLE] and can be acquired from the DNS
server, it is is overwritten by the DNS server value which is acquired externally. When the value is [0.0.0.0], the server is not set.)
[SECONDARY DNS]:
Secondary DNS server setting (Factory setting: [0.0.0.0]) (When [DHCP] is set to [ENABLE] and can be acquired from the
DNS server, it is is overwritten by the DNS server value which is acquired externally. When the value is [0.0.0.0], the server is not set.)
3
Select [WLAN] in the main menu → [I/F SETUP] → [USB/LAN] → [NETWORK SEL].
If the setting is changed, the camera will restart as necessary.
4
Enter information on the wireless access point to connect to.
Select [MANUAL] in [SSID INPUT MODE].
Enter SSID of the wireless access point for destination in [SSID] of the camera.
Select the encryption method to be used from the camera’s [ENCRYPTION].
f Factory setting: [WPA2-AES]
Enter a password of the wireless access point for destination in [ENCRYPT KEY] of the camera.
5
Check the network connection.
When the setting is completed, confirm that network connection between the camera and the wireless access point is made properly.
When network connection is made properly, the network status icon at the upper right of the thumbnail screen changes in yellow, and applications
(P2 Browser, FTP client function) which require network can be used.
@ @
NOTE
t The startup time after turning on the power may be longer due to starting of the network.
t When you change the settings of [NETWORK SEL], the changes will not be reflected until the camera is restarted. After the settings have been
changed, the setting screen termination may take time due to the restart of the network service.
t The IP address, subnet mask, and default gateway must be correctly set.
If the [CANNOT ACCESS GATEWAY!] warning appears at the termination of the setting screen, contact the administrator of the network you are
currently using.
t IP addresses from [192.168.255.0] to [192.168.255.255] cannot be used because they are reserved by the system.
t If you do not use default gateway and DNS, set them to [0.0.0.0].
t DHCP and DNS may not function properly depending on the network environment.
[INFRA] mode (when SSID is selected from the list)
Use the following procedures when the wireless access point to connect to is selected from a list.
1
Select [INFRA] in main menu
→
[I/F SETUP]
→
[USB/LAN]
→
[WIRELESS PROPERTY]
→
[TYPE].
2
If necessary, set each item in main menu → [I/F SETUP] → [USB/LAN] → [WIRELESS PROPERTY].
[MAC ADDRESS]: MAC address of the wireless LAN (cannot be changed)
[BAND]: Setting that switches between 2 transmission methods (2.4 GHz or 5 GHz) (Factory setting: [2.4GHz]) (Cannot be set)
[CHANNEL (2.4GHz)]: Channel used when set to 2.4 GHz (Factory setting: [AUTO]) (Cannot be set)
[CHANNEL (5GHz)]: Channel used when set to 5 GHz (Factory setting: [AUTO]) (Cannot be set)
[DHCP]: Setting whether to use automatic acquisition via DHCP ( [ENABLE]: Uses the automatic acquisition/ [DISABLE]: Does not use the
automatic acquisition) (Factory setting: [ENABLE])
[IP ADDRESS]: IP address of the camera (Factory setting: [192.168.0.1]).
[SUBNET MASK]: Subnet mask (Factory setting: [255.255.255.0])
[DEFAULT GATEWAY]: Default gateway (Factory setting: [192.168.0.254])
[PRIMARY DNS]: Primary DNS server setting (Factory setting: [0.0.0.0]) (When [DHCP] is set to [ENABLE] and can be acquired from the DNS
server, the DNS server value which is acquired externally is overwritten. When the value is [0.0.0.0], the server is not set.)
[SECONDARY DNS]: Secondary DNS server setting (Factory setting: [0.0.0.0]) (When [DHCP] is set to [ENABLE] and can be acquired from the
DNS server, the DNS server value which is acquired externally is overwritten. When the value is [0.0.0.0], the server is not set.)
3
Select [WLAN] in main menu
→
[I/F SETUP]
→
[USB/LAN]
→
[NETWORK SEL].
If the setting is changed, the camera will restart as necessary.
4
Enter information on the wireless access point to connect to.
1) Select [SELECT] in [SSID INPUT MODE].
2) Press the cursor buttons to select SSID, and press the <SET> button.
f “SSID connection destination list screen” (page 231) is displayed.
f You can delete the selected SSID from the connection history by selecting SSID and pressing the <EXIT> button while the <SHIFT> button is
pressed, or by pushing the <MARKER SEL>/<MODE CHECK/MENU CANCEL> switch towards the <MCK/MCL> side.
f You can clear all the SSID connection history by selecting [DELETE ALL HISTORY] and pressing the <SET> button.
3) Enter the password of the wireless access point to connect to the camera’s [ENCRYPT KEY].
5
Check the network connection.
When the setting is completed, confirm that network connection between the camera and the wireless access point is made properly.
When network connection is made properly, the network status icon at the upper right of the thumbnail screen changes in yellow, and applications
(P2 Browser, FTP client function) which require a network connection can be used.
@ @
NOTE
t The startup time after turning on the power may be longer due to starting of the network.