background image

24

ENGLISH

Autodos M

MA60-10E

ENGLISH

Autodos M 

MA60-10E

Configuration - Autodos M2 free chlorine/redox, pH

Line

Text

Setting

Explanation

-01

FLo

Selection of flow switch and alarm for low flow.

oFF

No flow switch. Flow alarm OFF.

Son

Flow switch that closes with flow. Flow alarm ON.

Pof

Turbine flow meter. Flow alarm OFF.

Pon*

Turbine flow meter. Flow alarm ON.

-02

FCL

Selection of electrode type for chlorine measurement.

Pb*

PB200, CLE2.2 or redox

Cur

4–20mA sensor e.g. CLE3

-03

C-o

Selection of chlorine or redox measurement

FCL*

Free chlorine

orP

Redox

-04

FCC

Selection of compensation of free chlorine against flow and/or pH.

non

No compensation.

Flo

Compensated against flow.

PH-

Compensated against pH.

FPH*

Compensated against flow and pH

-05

PHd

Selection of pH-adjusted dosing.

ACi*

Doses acid (doses when actual value > set value).

bAS

Doses alkali (doses when actual value < set value).

-06

PHc

Selection of pH calibration point 2. 

Calibration point 1 = pH 7.00

PH9*

Calibration point 2 = pH 9.00

PH4

Calibration point 2 = pH 4.00

-07

PC

Setting of access from PC.

No*

No access (display only).

rES

Alarm reset only.

Prg

Fully programmable.

-08

Sio

001-255   (001*)

Selection of Modbus ID number

-09

FLd

000-030   (000*)   [minutes]

Flow alarm delay time.

-10

rEL

000-030   (000*)   [minutes]

Alarm relay delay time.

-11

SbY

The SbY input blocks all dosing plus the alarm relay.

rEL*

Activates the alarm.

non

Does not activate the alarm.

* Factory default!

Содержание Autodos M1




































Отзывы: