Pacific energy FP25 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 40

Pacific energy FP25 Скачать руководство пользователя страница 30

WARNING: ALL ELECTRICAL WIRING MUST BE DONE BY A QUALIFIED ELECTRICIAN.

NOTE: For best results, the remote heat kit blower/s should be wired to a separate switch or speed control-
ler in the room that the outlet is in. If the outlet(s) are mounted in the chase they could be wired on the same
switch or speed controller as the Fireplace Blower.

Consult local codes or, in the absence of local codes, with the current CSA C22.1 Canadian Electrical Code or
in the USA,the National Electrical Code, ANSI/NFPA 70 (Latest Edition).

The Remote Heat Kit blower's electrical rating: 120V, 60HZ, 80 watts. For your protection against shock haz-
ard, use only a properly grounded electrical supply.

This kit includes a junction box, rheostat and cover plate. The junction box should be mounted in a conve-
nient location away from the fireplace.

Remote Heat Kit Wiring

Hot (black)

Neutral (white)

WALL SWITCH/

SPEED CONTROLLER

Blower

Ground

Terminal Strip

Use only copper conductors

Figure 27: T120-WODC remote heat kit wiring diagram.

30

100001385_071118-40

FP25

«
...
28
29
30
31
32
...
»

Содержание FP25









































Отзывы:

Нет отзывов