Oval D-160TS-7-E страница 46 Скачать руководство пользователя

Страница: 46 / 56

D-160TS-7-E

（

）

Converter

Where:

Maximum current of pulse output in actual use

Supply voltage

Maximum current of status output in actual use

Maximum current consumption of the ﬂowmeter

Cable resistance between receiving instrument and converter

Item

Description

Model

PA21 converter

Configuration

Separately mounted

Power source

24 to 32VDC

Power consumption

32V 40mA or less (24V 54mA or less)

Ambient
temperature

Non-explosionproof

−20 to +60

℃

(no condensation)

Explosionproof

−20 to +55

℃

(no condensation)

Finish

Body: Munsell 10B8/4, Cover: Munsell 2.5PB4/10

IP rating

IP67

Transmission
length

Sensor to
converter

Exclusive 5-wire cable Max. 30m

(Finished cable O.D.: 10.7 ± 0.5mm)

Converter to
receiving
instrument

For pulse output: 3-wire shielded cable max. 1km (See NOTE.)

For pulse and status output: 4-wire shielded cable max. 1km (See NOTE.)

CEVS, CVVS equivalent (Finished cable O.D.: 10.1 to 13mm)

Output signal

①

Pulse output: Open drain (equivalent to open collector)

Max. applied voltage: 30VDC, Allowable current: 50mA
Unfactored pulse
Pulse width: 0.2msec or 1msec

②

Status output: Open drain (equivalent to open collector)

Max. applied voltage: 30VDC, Allowable current: 50mA
Select from: Error, Error+Alarm, H/L alarm, Error+H/L alarm

Explosionproof
configuration

Converter

Ex d e

Ⅱ

C T6

Sensor

Amplifier part: Ex d [ib]

Ⅱ

C T4, Sensor part: Ex ib

Ⅱ

C T4, Applicable temp.

range: -20 to +72

℃

Cable
connection

Converter

G3/4 (internal thread)

Sensor

G1/2 (internal thread)

Explosionproof model: Union clamp of the accompanying pressure-tight

packing G3/4 (internal thread)

Installation

Mounted on 2" pipe stanchion (clamp and U-bolts furnished)

Display

LCD display

% ﬂow rate, error, alarm

NOTE

：

If the wire length exceeds 250m or the cable of less than 1.25mm

is used, the resistance of

the cable connecting the receiving instrument and the converter must satisfy the following
conditions considering voltage drop:

①

Low level of pulse output must satisfy the input condition of the receiving instrument:

Low level of pulse output = (If+2Ip+Is) R+0.5

②

Voltage between POWER and COMMON of the converter is within the rated voltage:

Converter voltage (between POWER and COMMON) = V−(2If+Ip+Is) R

Содержание D-160TS-7-E

























































Результаты поиска

Содержание D-160TS-7-E

Отзывы:

Похожие инструкции для D-160TS-7-E

Бренды по названию

Популярные бренды

Oval D-160TS-7-E, Инструкция по эксплуатации

Результаты поиска

Содержание D-160TS-7-E

Отзывы:

Похожие инструкции для D-160TS-7-E

Бренды по названию

Популярные бренды