Oval D-160TS-7-E страница 10 Скачать руководство пользователя | Manualshive

Страница: 10 / 56

background image

D-160TS-7-E

10

6.2 Pipes to be Used

Upstream and downstream pipes adjacent to the flowmeter should be of the same internal
diameter (ID) as the flowmeter. (The exclusive flow straightener, Honey Vane L, and downstream
short pipe have the same ID as the flowmeter.) The table below shows the standard ID of the
flowmeter. Confirm the delivery specification in case ID is non-standard.

Flowmeter standard ID

Nominal size

ID reference

under 400mm

Sch40

400mm or more

Sch20

6.3 Pressure Gage and Thermometer Taps

If pressure or temperature detection is necessary, provide the probes downstream of the flowmeter (see the
below figure). To avoid disturbances in the flow, temperature detection should be made downstream of the
flowmeter and, at the same time, upstream of the control valve.

Fig. 6.4

6.4 Meter Orientation

The flowmeter may be installed either on a horizontal line or a vertical line.
In a horizontal line, the sensor should not be installed upside down.

Fig. 6.5

Fig. 6.6

In outdoor installations, the meter

should not be installed with conduit

connection openings upward to prevent

rainwater, etc. from entering the meter.

CAUTION:

2 to 7D

from the meter

FLOW

D: Nominal size

Pressure detection point

Temperature detection point

Min. 1D from pressure detection point

Min. 2D from flowmeter

«
...
8
9
10
11
12
...
»

Содержание D-160TS-7-E

























































Отзывы:

Нет отзывов

Похожие инструкции для D-160TS-7-E

Бренд: Keithley Страницы: 73

Бренд: Raytech Страницы: 18

Бренд: SAGEMCOM Страницы: 33

Бренд: velocomp Страницы: 4

Бренд: IFM Страницы: 38

Бренд: Primes Страницы: 56

Arrow Mobile Android

Бренд: MADDALENA Страницы: 12

Бренд: Hanna Instruments Страницы: 16

Бренд: Apera Страницы: 2

Бренд: Bamo Страницы: 2

Druck DryTC 165

Бренд: Baker Hughes Страницы: 130

Бренд: Ocean Reef Страницы: 20

Бренд: E+E Elektronik Страницы: 3

Celviano GP-300

Бренд: Casio Страницы: 78

Бренд: Doepke Страницы: 2

Бренд: Apera Instruments Страницы: 32

Бренд: Thermal Gas Systems Страницы: 13

Бренд: TESTO Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды