Orion BuckEye Cam RC-5030 Скачать руководство пользователя страница 13

Страница: 13 / 62

4. ORION Camera System Overview

The following figure illustrates the exterior of the camera.

Antenna Connector

– Connect a supplied antenna to this connector. You

can purchase a high-gain antenna to increase the transmission distance.
Visit

www.buckeyecam.com

or contact BuckEye Cam for the list of

available high-gain antennae.

Connector for Solar panel or Battery Pack

– Connect an external battery

pack or a solar panel to increase the battery life of the camera.

Light Sensor

– Camera uses the light sensor to determine the amount of

light and exposure when it is capturing a picture.

Motion Sensor

– Passive Infrared sensor is used to detect motion of

animals and people.

IR Illuminator

– Infrared illuminator is used to capture pictures at night

without being detected.

ORION - Owner's Manual, Rev. 3.6

Antenna
Connector

Connector for
Solar Panel or
Battery Pack

Motion Sensor

IR Illuminators

Camera Lenses

Light Sensor

Содержание BuckEye Cam RC-5030































































Результаты поиска

Содержание BuckEye Cam RC-5030

Отзывы:

Похожие инструкции для BuckEye Cam RC-5030

Бренды по названию

Популярные бренды

Orion BuckEye Cam RC-5030, Руководство пользователя

Результаты поиска

Содержание BuckEye Cam RC-5030

Отзывы:

Похожие инструкции для BuckEye Cam RC-5030

Бренды по названию

Популярные бренды