Orion BuckEye Cam RC-5030 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 62

background image

5. Portable System Setup

25

Camera #1,

C-02

for Camera #2, and etc.

NOTE: If the selected camera is in low battery mode, the display
will have

LowBat

message while that camera is selected. The

battery on that camera will need to be charged or replaced.

3. Once the camera is selected, press

SELECT button. The Portable Base
will contact the selected camera
and request the battery level. Once
the camera returns the battery
level, it will be shown on the display. The bar will indicate the
current battery level on the selected camera. If the Portable Base
cannot contact the camera,

NO COM

message will be shown on

the display. In this case, test the battery level again. Make sure the
camera is turned on and the antennae on the camera and base are
properly connected.

To check the camera battery level at the camera, press the

BATTERY

button. The battery level will be shown on the display.

5.9. Taking a Test Picture

You can remotely tell the camera to take a test picture from the Portable
Base by completing the following steps.

1. Press

MENU

button on the base.

2. Use

UP

/

DOWN

buttons to scroll until

TAKPIC

is displayed

3. Press

SELECT

button.

4. Press

UP

/

DOWN

buttons to select the camera that you want to take

the picture. The camera number will be shown in the upper right
corner of the display.

5. Once the camera is selected, press

SELECT

button. The base will

send a command to the camera to take a picture. During this process
the display will show

-WAIT-

message. When the picture has been

taken the base will display

TAKEOK

message.

Please note that transmission of the picture may not start immediately since
the camera will compress the picture first.

5.10. Receiving Pictures from the Camera

Pictures from remote cameras are transmitted automatically and no special
commands are required to initiate the transfer. As the Portable Base
receives pictures from remote camera it will be saving them to the memory
card.

ORION - Owner's Manual, Rev. 3.6

«
...
25
26
27
28
29
...
»

Содержание BuckEye Cam RC-5030































































Отзывы:

Нет отзывов

Похожие инструкции для BuckEye Cam RC-5030

Бренд: Dash Страницы: 2

Бренд: Panasonic Страницы: 138

Бренд: HuddleCamHD Страницы: 18

Бренд: Perel Страницы: 20

Бренд: Ikegami Страницы: 35

Бренд: Vitek Страницы: 28

Trophy Cam 119636C

Бренд: Bushnell Страницы: 36

HOMEGUARD HGNVK-930CAM

Бренд: Iget Страницы: 6

Бренд: D-MAX Страницы: 48

Бренд: Air Techniques Страницы: 28

Бренд: X10 Страницы: 7

Бренд: ZKTeco Страницы: 73

Бренд: ZKVision Страницы: 76

85/1,4 IF Aspherical

Бренд: WalimeXPro Страницы: 7

Бренд: Navico Страницы: 2

Бренд: Vicon Страницы: 21

Predator Hybrid PREDHYB-PSU-SM

Бренд: 360 Vision Страницы: 50

Бренд: Domar Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды