ORiNG DGS-7084GCP-AIO_S SERIES Скачать руководство пользователя страница 6

Страница: 6 / 138

DGS-7084GCP-AIO_S SERIES User’s Manual

ORing Industrial Networking Corp

etting to Know Your Switch

1.1 About the DGS-7084GCP-AIO_S Industrial

Switch

DGS-7084GCP-AIO_S series are managed redundant ring Ethernet switch with 8xGigabit

combo ports and 4x1000Base-X SFP ports. With completely support of Ethernet

Redundancy protocol,

O-Ring

(recovery time < 30ms over 250 units of connection) and

MSTP/RSTP/STP (IEEE 802.1s/w/D) can protect your mission-critical applications from

network interruptions or temporary malfunctions with its fast recovery technology. ORing’s

thunder switch series provide advanced IP-based bandwidth management which can limit the

maximum bandwidth for each IP device. User can configure IP camera and NVR with more

bandwidth and limit other device bandwidth. ORing’s thunder switch series also support

application-based QoS. Application-based QoS can set highest priority for data stream

according to TCP/UDP port number. ORing’s special Device Binding function can permit only

allowed IP address with MAC address to access the networking. Hacker cannot access the

IP surveillance network without permission. It can avoid hacker from stealing video privacy

data and attacking IP camera, NVR and controllers. ORing’s thunder series switch also

provided advanced DOS/DDOS auto prevention. If there is any IP flow become big in short

time, ORing’s thunder switch will lock the source IP address for certain time to prevent the

attack. It’s hardware based prevention so it can prevent DDOS attack without using CPU

resource. DGS-7084GCP-AIO_S series includes 2 sets of bypass ports that protect the

network from failures and Network maintenance by ensuring network integrity during power

loss. Each set of these bypass ports includes Network ports and Monitor ports. The

Network ports are used for connection to main-network connections and provide protection

mechanism, and the Monitor ports are used for down-linking local networking device. When

the power is on, the operating mode of the Bypass ports is set to Normal, and the local

networking device is connected with main-network. When power failure occurs, the Bypass

port(s) is/are swiftly set to bypass mode to isolate the main-network from the local networking

device. And all functions of DGS-7084GCP-AIO_S series can also be managed centralized

and convenient by Open-Vision, Except the Web-based interface, Telnet and console (CLI)

configuration. Therefore, the switch is one of the most reliable choice for highly-managed

and Gigabit Fiber Ethernet application.

Содержание DGS-7084GCP-AIO_S SERIES











































































































































Результаты поиска

Содержание DGS-7084GCP-AIO_S SERIES

Отзывы:

ORiNG DGS-7084GCP-AIO_S SERIES, Руководство пользователя, Страница: 6 / 138

Результаты поиска

Содержание DGS-7084GCP-AIO_S SERIES

Отзывы: